diff options
Diffstat (limited to 'include/configs/MPC8560ADS.h')
| -rw-r--r-- | include/configs/MPC8560ADS.h | 170 |
1 files changed, 85 insertions, 85 deletions
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index 0d844d1c0b8..44b128fd6b5 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -31,22 +31,22 @@ #define __CONFIG_H /* High Level Configuration Options */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ -#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */ -#define CONFIG_MPC8560 1 /* MPC8560 specific */ -#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific*/ - -#undef CONFIG_PCI /* pci ethernet support */ -#define CONFIG_TSEC_ENET /* tsec ethernet support*/ -#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ +#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */ +#define CONFIG_MPC8560 1 /* MPC8560 specific */ +#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */ + +#undef CONFIG_PCI /* pci ethernet support */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ #define CONFIG_ENV_OVERWRITE -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ #if defined(CONFIG_MPC85xx_REV1) -#define CONFIG_DDR_DLL /* possible DLL fix needed */ +#define CONFIG_DDR_DLL /* possible DLL fix needed */ #endif /* Using Localbus SDRAM to emulate flash before we can program the flash, @@ -54,10 +54,10 @@ */ #undef CONFIG_RAM_AS_FLASH -#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */ -#define CONFIG_SYS_CLK_FREQ 66000000/* sysclk for MPC85xx */ +#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */ +#define CONFIG_SYS_CLK_FREQ 66000000/* sysclk for MPC85xx */ #else -#define CONFIG_SYS_CLK_FREQ 33000000/* most pci cards are 33Mhz */ +#define CONFIG_SYS_CLK_FREQ 33000000/* most pci cards are 33Mhz */ #endif #if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */ @@ -65,15 +65,15 @@ #endif /* below can be toggled for performance analysis. otherwise use default */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#undef CONFIG_BTB /* toggle branch predition */ -#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#undef CONFIG_BTB /* toggle branch predition */ +#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */ -#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00200000 /* memtest region */ -#define CFG_MEMTEST_END 0x00400000 +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00200000 /* memtest region */ +#define CFG_MEMTEST_END 0x00400000 #if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \ defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \ @@ -85,48 +85,48 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE -#define CFG_SDRAM_SIZE 128 /* DDR is 128MB */ +#define CFG_SDRAM_SIZE 128 /* DDR is 128MB */ #if defined(CONFIG_RAM_AS_FLASH) -#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */ +#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */ #else -#define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */ +#define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */ #endif #define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ #if defined(CONFIG_RAM_AS_FLASH) -#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */ -#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */ +#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */ +#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */ #else /* Boot from real Flash */ -#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */ -#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */ +#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */ +#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */ #endif -#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */ +#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */ #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 64 /* sectors per device */ +#define CFG_MAX_FLASH_SECT 64 /* sectors per device */ #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) #define CFG_RAMBOOT #else -#undef CFG_RAMBOOT +#undef CFG_RAMBOOT #endif -#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ +#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ #if defined(CONFIG_DDR_SETTING) -#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ +#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ #define CFG_DDR_CS0_CONFIG 0x80000002 #define CFG_DDR_TIMING_1 0x37344321 #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/ @@ -138,9 +138,9 @@ #undef CONFIG_CLOCKS_IN_MHZ /* local bus definitions */ -#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ +#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ #define CFG_OR2_PRELIM 0xfc006901 -#define CFG_LBC_LCRR 0x00030004 /* local bus freq */ +#define CFG_LBC_LCRR 0x00030004 /* local bus freq */ #define CFG_LBC_LBCR 0x00000000 #define CFG_LBC_LSRT 0x20000000 #define CFG_LBC_MRTPR 0x20000000 @@ -151,78 +151,78 @@ #define CFG_LBC_LSDMR_5 0x4061b723 #if defined(CONFIG_RAM_AS_FLASH) -#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */ +#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */ #else -#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */ +#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */ #endif #define CFG_OR4_PRELIM 0xffffe1f1 #define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000) #define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ -#define CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else */ -#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ -#define CONFIG_BAUDRATE 115200 +#define CONFIG_BAUDRATE 115200 #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} /* Use the HUSH parser */ #define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER #define CFG_PROMPT_HUSH_PS2 "> " #endif /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ #define CFG_PCI_MEM_BASE 0xe0000000 #define CFG_PCI_MEM_PHYS 0xe0000000 #define CFG_PCI_MEM_SIZE 0x10000000 -#if defined(CONFIG_PCI) /* PCI Ethernet card */ +#if defined(CONFIG_PCI) /* PCI Ethernet card */ #define CONFIG_NET_MULTI #define CONFIG_EEPRO100 #undef CONFIG_TULIP -#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ #if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xe0000000 - #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ + #define PCI_ENET0_IOADDR 0xe0000000 + #define PCI_ENET0_MEMADDR 0xe0000000 + #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ #endif -#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ -#if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 7 */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ +#if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 7 */ #define CFG_PCI_SUBSYS_DEVICEID 0x0003 #else #define CFG_PCI_SUBSYS_DEVICEID 0x0009 #endif -#elif defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ -#define CONFIG_NET_MULTI 1 -#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */ +#elif defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ +#define CONFIG_NET_MULTI 1 +#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 8 /* PHY address */ #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ -#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ -#undef CONFIG_ETHER_NONE /* define if ether on something else */ -#define CONFIG_ETHER_INDEX 2 /* which channel for ether */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 2 /* which channel for ether */ #if (CONFIG_ETHER_INDEX == 2) /* * - Rx-CLK is CLK13 @@ -230,15 +230,15 @@ * - Select bus for bd/buffers * - Full duplex */ - #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) - #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) - #define CFG_CPMFCR_RAMTYPE 0 - #define CFG_FCC_PSMR (FCC_PSMR_FDE) + #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) + #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) + #define CFG_CPMFCR_RAMTYPE 0 + #define CFG_FCC_PSMR (FCC_PSMR_FDE) #define FETH2_RST 0x01 #elif (CONFIG_ETHER_INDEX == 3) /* need more definitions here for FE3 */ #define FETH3_RST 0x80 - #endif /* CONFIG_ETHER_INDEX */ + #endif /* CONFIG_ETHER_INDEX */ #define CONFIG_MII /* MII PHY management */ #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ /* @@ -267,7 +267,7 @@ #else #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) - #define CFG_ENV_SECT_SIZE 0x40000 /* 128K(one sector) for env */ + #define CFG_ENV_SECT_SIZE 0x40000 /* 128K(one sector) for env */ #endif #define CFG_ENV_SIZE 0x2000 #else @@ -320,7 +320,7 @@ * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "MPC8560ADS=> " /* Monitor Command Prompt */ +#define CFG_PROMPT "MPC8560ADS=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else @@ -361,17 +361,17 @@ /*Note: change below for your network setting!!! */ #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) -#define CONFIG_ETHADDR 00:01:af:07:9b:8a -#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b -#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c +#define CONFIG_ETHADDR 00:01:af:07:9b:8a +#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b +#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c #endif -#define CONFIG_SERVERIP 163.12.64.52 -#define CONFIG_IPADDR 10.82.0.105 +#define CONFIG_SERVERIP 163.12.64.52 +#define CONFIG_IPADDR 10.82.0.105 #define CONFIG_GATEWAYIP 10.82.1.254 #define CONFIG_NETMASK 255.255.254.0 -#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003 -#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx -#define CONFIG_BOOTFILE pImage +#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003 +#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx +#define CONFIG_BOOTFILE pImage #endif /* __CONFIG_H */ |