diff options
Diffstat (limited to 'include/configs/ezkit533.h')
| -rw-r--r-- | include/configs/ezkit533.h | 188 |
1 files changed, 0 insertions, 188 deletions
diff --git a/include/configs/ezkit533.h b/include/configs/ezkit533.h deleted file mode 100644 index 5eda6732ca7..00000000000 --- a/include/configs/ezkit533.h +++ /dev/null @@ -1,188 +0,0 @@ -#ifndef __CONFIG_EZKIT533_H__ -#define __CONFIG_EZKIT533_H__ - -#define CFG_LONGHELP 1 -#define CONFIG_BAUDRATE 57600 -#define CONFIG_STAMP 1 -#define CONFIG_BOOTDELAY 5 - -#define CONFIG_DRIVER_SMC91111 1 -#define CONFIG_SMC91111_BASE 0x20310300 -#if 0 -#define CONFIG_MII -#define CFG_DISCOVER_PHY -#endif - -#define CONFIG_RTC_BF533 1 -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ - -/* CONFIG_CLKIN_HZ is any value in Hz */ -#define CONFIG_CLKIN_HZ 27000000 -/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ -/* 1=CLKIN/2 */ -#define CONFIG_CLKIN_HALF 0 -/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ -/* 1=bypass PLL */ -#define CONFIG_PLL_BYPASS 0 -/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */ -/* Values can range from 1-64 */ -#define CONFIG_VCO_MULT 22 -/* CONFIG_CCLK_DIV controls what the core clock divider is */ -/* Values can be 1, 2, 4, or 8 ONLY */ -#define CONFIG_CCLK_DIV 1 -/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */ -/* Values can range from 1-15 */ -#define CONFIG_SCLK_DIV 5 - -#if ( CONFIG_CLKIN_HALF == 0 ) -#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) -#else -#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) -#endif - -#if (CONFIG_PLL_BYPASS == 0) -#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) -#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) -#else -#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ -#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ -#endif - -#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */ -#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */ -#define CONFIG_MEM_MT48LC16M16A2TG_75 1 - -#define CONFIG_LOADS_ECHO 1 - - -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_PING | \ - CFG_CMD_ELF | \ - CFG_CMD_I2C | \ - CFG_CMD_JFFS2 | \ - CFG_CMD_DATE) -#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off" - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include <cmd_confdefs.h> - -#define CFG_PROMPT "ezkit> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x01F00000 /* 1 ... 31 MB in DRAM */ -#define CFG_LOAD_ADDR 0x01000000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_MAX_RAM_SIZE 0x02000000 -#define CFG_FLASH_BASE 0x20000000 - -#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN) -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN) -#define CFG_GBL_DATA_SIZE 0x4000 -#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE) -#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4) - -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -#define CFG_FLASH0_BASE 0x20000000 -#define CFG_FLASH1_BASE 0x20200000 -#define CFG_FLASH2_BASE 0x20280000 -#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 40 /* max number of sectors on one chip */ - -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_ADDR 0x20020000 -#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */ - -/* JFFS Partition offset set */ -#define CFG_JFFS2_FIRST_BANK 0 -#define CFG_JFFS2_NUM_BANKS 1 -/* 512k reserved for u-boot */ -#define CFG_JFFS2_FIRST_SECTOR 11 - - -/* - * Stack sizes - */ -#define CONFIG_STACKSIZE (128*1024) /* regular stack */ - -#define POLL_MODE 1 -#define FLASH_TOT_SECT 40 -#define FLASH_SIZE 0x220000 -#define CFG_FLASH_SIZE 0x220000 - -/* - * Initialize PSD4256 registers for using I2C - */ -#define CONFIG_MISC_INIT_R - -/* - * I2C settings - * By default PF1 is used as SDA and PF0 as SCL on the Stamp board - */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -/* - * Software (bit-bang) I2C driver configuration - */ -#define PF_SCL PF0 -#define PF_SDA PF1 - -#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;") -#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;") -#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;") -#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;") -#define I2C_SDA(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SDA; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SDA; \ - asm("ssync;"); \ - } -#define I2C_SCL(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SCL; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SCL; \ - asm("ssync;"); \ - } -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -#define CFG_I2C_SPEED 50000 -#define CFG_I2C_SLAVE 0xFE - - -#define __ADSPLPBLACKFIN__ 1 -#define __ADSPBF533__ 1 - -/* 0xFF, 0x7BB07BB0, 0x22547BB0 */ -/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN) -#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \ - ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN) -#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \ - B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN) -*/ -#define AMGCTLVAL 0xFF -#define AMBCTL0VAL 0x7BB07BB0 -#define AMBCTL1VAL 0xFFC27BB0 - -#define CONFIG_VDSP 1 - -#ifdef CONFIG_VDSP -#define ET_EXEC_VDSP 0x8 -#define SHT_STRTAB_VDSP 0x1 -#define ELFSHDRSIZE_VDSP 0x2C -#define VDSP_ENTRY_ADDR 0xFFA00000 -#endif - -#endif |