diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/tricorder.h | 236 |
1 files changed, 0 insertions, 236 deletions
diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h deleted file mode 100644 index 55f25857eb3..00000000000 --- a/include/configs/tricorder.h +++ /dev/null @@ -1,236 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2006-2008 - * Texas Instruments. - * Richard Woodruff <r-woodruff2@ti.com> - * Syed Mohammed Khasim <x0khasim@ti.com> - * - * (C) Copyright 2012 - * Corscience GmbH & Co. KG - * Thomas Weber <weber@corscience.de> - * - * Configuration settings for the Tricorder board. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_MACH_TYPE MACH_TYPE_TRICORDER -/* - * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM - * 64 bytes before this address should be set aside for u-boot.img's - * header. That is 0x800FFFC0--0x80100000 should not be used for any - * other needs. - */ - -#include <asm/arch/cpu.h> /* get chip and board defs */ -#include <asm/arch/omap.h> - -/* Clock Defines */ -#define V_OSCK 26000000 /* Clock output from T2 */ -#define V_SCLK (V_OSCK >> 1) - -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG -#define CONFIG_REVISION_TAG - -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (1024*1024) - -/* Hardware drivers */ - -/* NS16550 Configuration */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ - -/* select serial console configuration */ -#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ - 115200} - -/* I2C */ -#define CONFIG_SYS_I2C - - -/* EEPROM */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_BUS_NUM 1 - -/* TWL4030 */ - -/* Board NAND Info */ -#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ - /* to access nand at */ - /* CS0 */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ - /* devices */ -#define CONFIG_SYS_NAND_MAX_OOBFREE 2 -#define CONFIG_SYS_NAND_MAX_ECCPOS 56 - -/* needed for ubi */ - -/* Environment information (this is the common part) */ - - -/* hang() the board on panic() */ - -/* environment placement (for NAND), is different for FLASHCARD but does not - * harm there */ -#define CONFIG_ENV_RANGE (384 << 10) /* allow badblocks in env */ - -/* the loadaddr is the same as CONFIG_SYS_LOAD_ADDR, unfortunately the defiend - * value can not be used here! */ -#define CONFIG_LOADADDR 0x82000000 - -#define CONFIG_COMMON_ENV_SETTINGS \ - "console=ttyO2,115200n8\0" \ - "mmcdev=0\0" \ - "vram=3M\0" \ - "defaultdisplay=lcd\0" \ - "kernelopts=mtdoops.mtddev=3\0" \ - "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ - "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ - "commonargs=" \ - "setenv bootargs console=${console} " \ - "${mtdparts} " \ - "${kernelopts} " \ - "vt.global_cursor_default=0 " \ - "vram=${vram} " \ - "omapdss.def_disp=${defaultdisplay}\0" - -#define CONFIG_BOOTCOMMAND "run autoboot" - -/* specific environment settings for different use cases - * FLASHCARD: used to run a rdimage from sdcard to program the device - * 'NORMAL': used to boot kernel from sdcard, nand, ... - * - * The main aim for the FLASHCARD skin is to have an embedded environment - * which will not be influenced by any data already on the device. - */ -#ifdef CONFIG_FLASHCARD -/* the rdaddr is 16 MiB before the loadaddr */ -#define CONFIG_ENV_RDADDR "rdaddr=0x81000000\0" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_COMMON_ENV_SETTINGS \ - CONFIG_ENV_RDADDR \ - "autoboot=" \ - "run commonargs; " \ - "setenv bootargs ${bootargs} " \ - "flashy_updateimg=/dev/mmcblk0p1:corscience_update.img " \ - "rdinit=/sbin/init; " \ - "mmc dev ${mmcdev}; mmc rescan; " \ - "fatload mmc ${mmcdev} ${loadaddr} uImage; " \ - "fatload mmc ${mmcdev} ${rdaddr} uRamdisk; " \ - "bootm ${loadaddr} ${rdaddr}\0" - -#else /* CONFIG_FLASHCARD */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_COMMON_ENV_SETTINGS \ - "mmcargs=" \ - "run commonargs; " \ - "setenv bootargs ${bootargs} " \ - "root=/dev/mmcblk0p2 " \ - "rootwait " \ - "rw\0" \ - "nandargs=" \ - "run commonargs; " \ - "setenv bootargs ${bootargs} " \ - "root=ubi0:root " \ - "ubi.mtd=7 " \ - "rootfstype=ubifs " \ - "ro\0" \ - "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ - "bootscript=echo Running bootscript from mmc ...; " \ - "source ${loadaddr}\0" \ - "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ - "mmcboot=echo Booting from mmc ...; " \ - "run mmcargs; " \ - "bootm ${loadaddr}\0" \ - "loaduimage_ubi=ubi part ubi; " \ - "ubifsmount ubi:root; " \ - "ubifsload ${loadaddr} /boot/uImage\0" \ - "loaduimage_nand=nand read ${loadaddr} kernel 0x500000\0" \ - "nandboot=echo Booting from nand ...; " \ - "run nandargs; " \ - "run loaduimage_nand; " \ - "bootm ${loadaddr}\0" \ - "autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \ - "if run loadbootscript; then " \ - "run bootscript; " \ - "else " \ - "if run loaduimage; then " \ - "run mmcboot; " \ - "else run nandboot; " \ - "fi; " \ - "fi; " \ - "else run nandboot; fi\0" - -#endif /* CONFIG_FLASHCARD */ - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ - -#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000) - -/* - * OMAP3 has 12 GP timers, they can be driven by the system clock - * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). - * This rate is divided by a local divisor. - */ -#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) -#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ - -/* Physical Memory Map */ -#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 -#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 - -/* NAND and environment organization */ -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 -#define CONFIG_SYS_INIT_RAM_SIZE 0x800 -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* Defines for SPL */ - -#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" - -#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \ - CONFIG_SPL_TEXT_BASE) - -#define CONFIG_SPL_BSS_START_ADDR 0x80000000 /*CONFIG_SYS_SDRAM_BASE*/ -#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 - -/* NAND boot config */ -#define CONFIG_SYS_NAND_5_ADDR_CYCLE -#define CONFIG_SYS_NAND_PAGE_COUNT 64 -#define CONFIG_SYS_NAND_PAGE_SIZE 2048 -#define CONFIG_SYS_NAND_OOBSIZE 64 -#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) -#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS -#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \ - 13, 14, 16, 17, 18, 19, 20, 21, 22, \ - 23, 24, 25, 26, 27, 28, 30, 31, 32, \ - 33, 34, 35, 36, 37, 38, 39, 40, 41, \ - 42, 44, 45, 46, 47, 48, 49, 50, 51, \ - 52, 53, 54, 55, 56} - -#define CONFIG_SYS_NAND_ECCSIZE 512 -#define CONFIG_SYS_NAND_ECCBYTES 13 -#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW - -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE - -#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000 -#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x100000 - -#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 -#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */ - -#endif /* __CONFIG_H */ |