| Age | Commit message (Collapse) | Author |
|---|
|
Marek Mojík <marek.mojik@nic.cz> says:
Hello all,
this is a continuation of previous work by Pali to add support for the
Turris 1.x board. As the patches were based on u-boot v2022.04, a
nontrivial rebasing was needed.
Some notes:
- Some options that are in SD defconfig are disabled in NOR defconfig
because over the years u-boot grew and the old NOR defconfig will not
fit into NOR memory.
- SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We
were not able to fix this yet)
|
|
Add support for CZ.NIC Turris 1.x routers.
CZ.NIC Turris 1.0 (RTRS01) and 1.1 (RTRS02) are open source routers, they
have dual-core PowerPC Freescale P2020 CPU and are based on reference
Freescale P2020RDB-PC-A board design.
Hardware design is fully open source, all firmware and hardware design
files are available at Turris project website:
https://docs.turris.cz/hw/turris-1x/turris-1x/
https://project.turris.cz/en/hardware.html
The P2020 BootROM can load U-Boot either from NOR flash or from SD card.
We add the new defconfigs, turris_1x_nor_defconfig, which configures
U-Boot for building the NOR image, and turris_1x_sdcard_defconfig, which
configures U-Boot for building an image suitable for SD card.
The defconfig for NOR image is stripped-down a - many config options
enabled in SD defconfig are disabled for NOR defconfig. This is because
U-Boot grew non-trivially in the last two years and it would not fit
into the space allocated for U-Boot in the NOR memory. In the future we
may try to use LTO to reduce the size of the code and enable more
options.
The design of CZ.NIC Turris 1.x routers is based on Freescale P2020RDB-PC-A
board, so some code from boards/freescale/p1_p2_rdb_pc is used and linked
into Turris 1.x board code.
Turris 1.x code in this patch uses modern distroboot and can boot Linux
kernel from various locations, including NAND, SD card, USB flash disks,
NVMe disks or SATA disks (connected to extra SATA/SCSI PCIe controllers).
Via distroboot is implemented also rescue NOR boot for factory recovery,
triggered by reset button, like on other existing Turris routers.
SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We were
not able to fix this yet)
[ Because various CONFIG_ macros were migrated to Kconfig since the last
time this worked on upstream U-Boot (in 2022), a non-trivial rebasing
was needed and some issues were solved. ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
|
|
include/asm/config.h
Use the CONFIG_IS_ENABLED() macro when checking for DM_SERIAL so that
CFG_SYS_NS16550_CLK is not defined as get_serial_clock() in SPL if SPL
does not have DM_SERIAL enabled.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
|
|
Use CONFIG_VAL() for SYS_MONITOR_BASE in start.S so that correct value
is used for SPL.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
|
|
The find_law() function searches for LAW just by physical address. This
is unsuitable for cases with overlapping LAWs. Extend it to
find_law_by_addr_id(), which searches for LAW by physical address and
target id.
Add a static inline definition of the original find_law() into fsl_law.h
header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
|
|
p1_p2_rdb_pc_fix_fdt_model() for fixing DT model string
This allows boards to fixup / overwrite DT model string when booting OS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
|
|
When U-Boot is running from flash memory (execute in place) then
gd->fdt_blob before relocation points to read-only flash memory.
So U-Boot calls board_fix_fdt() with read-only gd->fdt_blob pointer which
cause immediate CPU crash when callback is trying to modify gd->fdt_blob.
Fix this issue by introducing a new config option OF_INITIAL_DTB_READONLY
which moves fix_fdt callback after the reloc_fdt callback. This makes
CONFIG_OF_BOARD_FIXUP working also if U-Boot before relocation is not
running from read/write (S)RAM memory.
This is required for mpc85xx boards when booting from flash NOR.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-raspberrypi
Updates for RPi for 2024.10:
- board: rpi: remove leftover CONFIG_HW_WATCHDOG block
- arm: bcm283x: remove unused empty hw_watchdog_disable
- board: raspberrypi: Fix format specifier for printing rev_scheme
- Revert "arm: dts: bcm283x: Add minimal smbios information"
|
|
This was added in commit 45a6d231b2f (bcm2835_wdt: support for the
BCM2835/2836 watchdog), which did do 'select HW_WATCHDOG'. That
incarnation of the watchdog driver later got removed in
c7adc0b5f98 (watchdog: bcm2835_wdt: Remove unused BCM283x watchdog
driver and its references), but this block was left behind.
Another rpi watchdog driver has since been added, but that does not
select HW_WATCHDOG, so this remains dead and unused. Remove it.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
|
|
This empty stub was originally added as one branch of an #ifdef in
commit 45a6d231b2f (bcm2835_wdt: support for the BCM2835/2836
watchdog). That incarnation of the rpi watchdog driver was later
removed in c7adc0b5f98 (watchdog: bcm2835_wdt: Remove unused BCM283x
watchdog driver and its references), but this now unused stub was left
behind. The later (re-)added rpi watchdog driver does not define a
hw_watchdog_disable() function, as that is properly integrated in the
watchdog framework.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
|
|
rev_scheme is an unsigned integer and must not be printed
as a signed integer.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
|
|
This reverts commit 33041972727e84d3f95e26c83322521f61827584.
With the ability to generate this SMBIOS details autmotically the
small amount of details that this patch provided are generated
automatically so this is now obsolete so we can just drop it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-dfu
u-boot-dfu-20240711
Usb gadget:
- A welcome cleanup: epautoconf workaround is dropped to use
.match_ep() instead
- Introduce handle_interrupts() op for USB_GADGET_GENERIC, which
allows a per-driver interrupt handling
Fastboot:
- Fix mssing include when building with TCP only
|
|
The build option to support images of type 'IMAGE_FORMAT_LEGACY' is
CONFIG_LEGACY_IMAGE_FORMAT so update the pytest to check for the correct
option.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The ARASAN MMC controller on Keystone 3 class of devices need the SDCD
line to be connected for proper functioning.
In cases where this can't be connected, add a quirk to force the
controller into test mode and set the TESTCD bit. Use the flag
"ti,fails-without-test-cd", to implement this above quirk when required.
Additionally, this quirk also avoids waiting for the controller debounce
time.
This commit is similar to linux kernel commit c7666240ec76
("drivers: mmc: sdhci_am654: Add the quirk to set TESTCD bit").
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
Add and use the correct number of ddr phy registers to update the
corresponding settings.
Fixes: cbf5c99ef317 ("board: phytec: common: Introduce a method to inject DDR timings deltas")
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
|
|
When building with the igep00x0_defconfig, the following warning is shown:
$ make -j $(nproc)
...
LD spl/u-boot-spl
OBJCOPY spl/u-boot-spl-nodtb.bin
SYM spl/u-boot-spl.sym
CAT spl/u-boot-spl-dtb.bin
COPY spl/u-boot-spl.bin
MKIMAGE MLO
===================== WARNING ======================
This board does not use CONFIG_DM_I2C (Driver Model
for I2C drivers). Please update the board to use
CONFIG_DM_I2C before the v2022.04 release. Failure to
update by the deadline may result in board removal.
See doc/develop/driver-model/migration.rst for more info.
====================================================
The only reason why I2C is enabled for the IGEP boards is that the TWL4030
driver requires it.
But both the TWL4034 and the OMAP I2C controller drivers were converted to
the driver model by commits daa69ffe3d4d ("drivers: i2c: omap24xx_i2c:
adopt omap_i2c driver to driver model") and fb1b7712ad3f power: make most
tps drivers and the twl4030 driver compatible with DM_I2C") respectively.
So there's no reason anymore to keep using the I2C legacy API and instead
the DM_I2C option could just be enabled.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
|
|
In some FDTs, there is not enough free memory to add nodes, so this
operation fails.
Signed-off-by: Maxim Moskalets <maximmosk4@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This allows spliting partition list to several lines in environment file
ex:
--------------------
gpt_partition_list=
name=boot1,size=5MiB,start=0x100000;
name=boot2,size=5MiB;
name=rootfs1,size=70MiB;
name=rootfs2,size=70MiB;
name=overlay1,size=20MiB;
name=overlay2,size=20MiB;
name=art,size=4MiB;
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Fixes a compile error when building with only the TCP fastboot
implementation.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240621015135.1570605-1-caleb.connolly@linaro.org
[mkorpershoek: wrapped commit msg to fix checkpatch]
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Christian Marangi <ansuelsmth@gmail.com> says:
This is an initial series that have all the initial trivial
fixes required for usage of OF_UPSTREAM for the mediatek SoC
This also contains the pcie-gen3 driver and the required tphy
support driver to make it work.
Subsequent series will follow with conversion of the mtk-clk
to permit usage of OF_UPSTREAM and upstream clk ID.
MT7981, MT7986 and MT7988 migration to upstream clock ID
is complete and working on MT7623.
Series CI tested with PR: https://github.com/u-boot/u-boot/pull/590
|
|
Support alternative compatible for fixed-plls clocks used upstream with
the compatible mediatek,mt7986-apmixedsys.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Support alternative compatible for fixed-plls clocks used upstream with
the compatible mediatek,mt7988-apmixedsys.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Set pcie-phy optional for PCIe gen3. MT7988 doesn't require it and
making it mandatory prevent the driver to correctly probe.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Upstream kernel linux define pinctrl for uart0, hence this pin group
and pinctrl driver is needed before relocation. Add DM_FLAG_PRE_RELOC
flag to init and mute mtk_serial error on early serial init.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Add support for gpio-controller property in root pinctrl node.
This is to follow upstream linux DTSI that doesn't define the
gpio-controller and cells in dedicated nodes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Support alternative compatible for fixed-plls clocks used upstream with
the compatible mediatek,mt7981-apmixedsys.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Add support for upstream linux clock and map U-Boot property to the one
use in upstream linux where supported.
Also add handling for the use_internal_cd that on upstream is hardcoded
enabled on mt7620.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Upstream linux serial driver use a different logic to setup serial regs.
They have 2 interval:
- < 115200 we use lowspeed regs and 16 * baud
- >= 115200 we use highspeed
We currently use force_highspeed property to force usage of highspeed
regs even with low baud rate.
Add special handling if the upstream compatible is used where we just
apply the same interval with anything >= 115200 in highspeed simulating
force_highspeed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Upstream linux also provide the additional optional bus clock.
Add support for it and also enable the baud and bus clock on probe.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Add support for optional arb and pmic clock for i2c provided in upstream
linux DTSI.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Handle alternative name for pn_swap property as upstream linux use
mediatek,pnswap.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Upstream kernel linux use a different compatible mediatek,spi-ipm.
Add support for this compatible and add handling for the additional
clock similar to how it's done by the upstream driver and handling for
all the property enabled by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Add MediaTek GEN3 PCIe controller support for filogic silicon.
This is adapted from the Linux version of the driver.
Signed-off-by: John Crispin <john@phrozen.org>
[ fix minor problems, fix checkpatch errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Add support for PHY type switch via the mediatek topmisc syscon.
This is needed on mt7981 to make the PCIe correctly work and display
LinkUp.
Follow the same implementation done on Linux kernel with the usage of
the mediatek,syscon-type property.
Example:
u3port0: usb-phy@11e10700 {
reg = <0x11e10700 0x900>;
clocks = <&topckgen CK_TOP_USB3_PHY_SEL>;
clock-names = "ref";
#phy-cells = <1>;
mediatek,syscon-type = <&topmisc 0x218 0>;
status = "okay";
};
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
There are operations in buildman that result in running the cross-tools
(such as performing size checks) and now that we have not modified PATH
to know where our tools are, these operations fail.
This reverts commit 6c0a3cf75f72370deec3ee516a9dd377397af207.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Add mvebu_espressobin_ultra-88f3720_defconfig (Benjamin)
- Update DTS for Thecus N2350 board (Tony)
- Add "old" Marvell DDR3 training for Armada 38x and Turris Omnia
(Marek)
- Misc turris_omnia changes (Marek)
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/21504
- Fixes for i.MX8M and i.MX93 clk-composite.
- Set CAN oscillator frequency based on model on verdin-imx8mm.
- Enable CAAM for phycore-imx8mp_defconfig.
- Miscellaneous improvements for Gateworks i.MX8M boards.
- Fix initramfs boot on msc_sm2s_imx8mp.
- Fixe EQoS on imx8mp-beacon-kit.
- Fix error message in fsl_esdhc_imx.
|
|
|
|
https://source.denx.de/u-boot/custodians/u-boot-sh
|
|
Currently, Armada 8k config header is setting boot devices and including
<config_distro_bootcmd.h> regardless of the CONFIG_DISTRO_DEFAULTS being
enabled or not, thus populating the environment for distro boot even on
devices that have no need for it.
So, lets simply respect the value of CONFIG_DISTRO_DEFAULTS.
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
|
Support old DDR3 training code on Turris Omnia, selectable via EEPROM
field.
Users experiencing DDR3 initialization failures or random crashes of the
operating system due to incorrect DDR3 configuration can select the old
DDR3 training implementation to fix those issues by setting the EEPROM
field "Use old DDR training":
eeprom update "Use old DDR training" 1
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
Add optional support for using old DDR3 training code from 2017.
The code lives in drivers/ddr/marvell/a38x/old/. To prevent symbol
clashing with new DDR3 training code, a special header which renames all
clashing symbols via macros is included and the symbols are prefixed
with 'old_'.
If old DDR3 training support is selected for a board, then the SPL
initialization code calls a new function
board_use_old_ddr3_training()
to check whether it should use old DDR3 training code. The default
weak implementation returns false, defaulting to new DDR3 training code.
Boards that wish to support this need to select the
ARMADA_38X_SUPPORT_OLD_DDR3_TRAINING
config option and implement the old version of DDR topology provider,
ddr3_get_topology_map().
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
Backport the option to compile with immutable debug settings also to
the old implementation of the DDR3 training code.
The original PR for mv-ddr-marvell can be seen at
https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/45/
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
Fix some compilation warning in the old DDR training code.
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
Import DDR training code from commit 1b69ce2fc0ec ("arm: mvebu:
ddr3_debug: remove self assignments") into
drivers/ddr/marvell/a38x/old/. The code is not used yet.
Explanation:
Since 2019, on some Turris Omnia boards we have been having problems
with newer versions of Marvell's DDR3 training code for Armada 38x,
which is ported from mv-ddr-marvell [1] to U-Boot into the
drivers/ddr/marvell/a38x/ directory:
- sometimes the DDR3 training fails on some older boards, sometime it
fails on some newer boards
- other times it succeeds, but some boards experience crashes of the
operating system after running for some time.
Using the stock version of Turris Omnia's U-Boot from solved these
issues, but this solution was not satisfactory, since we wanted
features from new U-Boot.
Back in 2020-2022 we have spent several months trying to debug the
issues, working with Marvell, on our own, and also with U-Boot
community, but these issues persist still.
One solution we used back in 2019 was a "hybrid U-Boot": the SPL part
(containing the DDR3 training code) was taken from the stock version,
while the proper part was current U-Boot at the time. This solution also
has its drawbacks, of which the main one is the need to glue binaries
from two separate builds.
Since then there have been some more changes to the DDR3 training code
in upstream mv-ddr-marvell that have been ported to U-Boot. We have
provided our users experimental builds of U-Boot in the TurrisOS so that
they could try upgrading the firmware and let us know if those problems
still exist. And they do.
We do not have the time nor manpower to debug this problem and fix it
properly. Marvell was also no able to provide a solution to this,
probably because they do not have the manpower as well.
I have therefore come up with this "not that pretty" solution: take the
DDR3 training code from an older version of U-Boot that is known to
work, put it into current U-Boot under old/ subdirectory within
drivers/ddr/marvell/a38x/, build into the SPL binary both the old and
new versions and make it possible to select the old version via an env
variable.
[1] https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
Some Turris Omnia boards experience memory issues, and by
experimentation we found that some of these issues can be solved by
slowing DDR speed.
Add a new field in the extended EEPROM information structure, ddr_speed.
Support several values in this field (for now 1066F, 1333H, and the
default, 1600K) and use it to overwrite the DDR topology parameters
used by the DDR training algorithm.
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
Extend the Omnia EEPROM information structure in preparation for more
variables to be stored there.
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
Enable the 'eeprom' command with support for EEPROM layout for Turris
Omnia. Enable the i2c-eeprom driver so that the EEPROM is accessed via
driver model.
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
Implement Turris Omnia EEPROM layout for the 'eeprom' command.
When the 'eeprom' command (with layout support) is enabled, we can now
use the 'eeprom print' and 'eeprom update' commands, for example:
=> eeprom print
Magic constant 34a04103
RAM size in GB 2
Wi-Fi Region
CRC32 checksum cecbc2a1
Signed-off-by: Marek Behún <kabel@kernel.org>
|
