aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-12-09Merge tag 'u-boot-stm32-20201209' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board - Update ARM STI and ARM STM STM32MP Arch maintainers emails - Enable internal pull-ups for SDMMC1 on DHCOM SoM
2020-12-09ARM: dts: stm32: Add USB OTG ID pin on DH AV96Marek Vasut
Add USB OTG ID pin mux and switch the USB OTG port from peripheral to OTG mode. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2020-12-09ARM: dts: stm32: Enable SDMMC3 on DH DRC02Marek Vasut
The DH DRC02 board has an on-board microSD slot, add DT properties to enable the slot. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2020-12-09ARM: dts: stm32: Disable SDMMC1 CKIN feedback clockMarek Vasut
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter or without one on the SDMMC1 interface. Because the SDMMC1 interface is limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback clock to permit operation of the same U-Boot image on both SoM with and without voltage level shifter. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2020-12-09ARM: dts: stm32: Enable internal pull-ups for SDMMC1 on DHCOM SoMMarek Vasut
The default state of SD bus and clock line is logical HI. SD card IO is open-drain and pulls the bus lines LO. Always enable the SD bus pull ups to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus voltage level shifter, the pull ups are built into the level shifter, however that has no negative impact. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2020-12-09.mailmap: map Patrick Delaunay and my email addressPatrice Chotard
Add our new email address dedicated for upstream activities. Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-12-09treewide: Update email address Patrick Delaunay and Patrice ChotardPatrice Chotard
Update Patrick and my email address with the one dedicated to upstream activities. Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-12-09MAINTAINERS: Update ARM STI and ARM STM STM32MP Arch maintainers emailsPatrice Chotard
Update Patrick and my email address with the one dedicated to upstream activities. Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-12-09add check for ignored CONFIG_ENV_EXT4_DEVICE_AND_PART definitionManuel Reis
Check whether user has explicitly defined device and partition where environment file will be located before using 'auto' i.e. bootable partition Voids the need to set such partition as bootable to work with the 'dev:auto' tuple Signed-off-by: Manuel Reis <mluis.reis@gmail.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Tested-by: Michael Opdenacker <michael.opdenacker@bootlin.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2020-12-08Merge https://gitlab.denx.de/u-boot/custodians/u-boot-imxTom Rini
2020-12-07Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Espressobin: Simplify DT handling of board variants (Pali) - Add Luka Perkov to maintainers of Puzzle-M801 (Luka) - Armada 38x: Enable board specific USB2 high-speed impedance threshold configuration (Joshua)
2020-12-07configs: migrate CONFIG_IMX_THERMAL to defconfigsTom Rini
Done via moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-12-07imx8mp_evk: README instruction fixesBaruch Siach
Use the full name of firmware self extracting file to make it run. Also, don't use sudo when not needed. Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2020-12-07doc: board: imx8qm-rom7720-a1.rst: convert readme to reSTOliver Graute
Convert README to reStructuredText format. Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
2020-12-07arm: mvebu: Espressobin: Detect presence of emmc at runtimePali Rohár
Try to initialize emmc in board_late_init() and if it fails then we know that emmc device is not connected. This allows to use in U-Boot just one DTS file for all Espressobin variants and also to correctly set fdtfile env variable for Linux kernel. Signed-off-by: Pali Rohár <pali@kernel.org> Tested-by: Gérald Kerma <gerald@gk2.net> Reviewed-by: Andre Heider <a.heider@gmail.com>
2020-12-07arm: mvebu: Espressobin: Add support for emmc into dts filePali Rohár
To simplify setup, configuration and compilation of u-boot, define emmc node for all Espressobin boards. Espressobin boards without populated emmc works correctly, just detection and initialization of emmc obviously fails. Code for emmc is extracted from commit f1a43c84a960 ("arm64: dts: a3720: add support for espressobin with populated emmc"). Signed-off-by: Pali Rohár <pali@kernel.org> Tested-by: Gérald Kerma <gerald@gk2.net>
2020-12-07Revert "arm64: dts: a3720: add support for espressobin with populated emmc"Pali Rohár
This reverts commit f1a43c84a960265309fa8365759de271a70c5a7e.
2020-12-07Revert "arm64: dts: armada-3720-espressobin: split common parts to .dtsi"Pali Rohár
This reverts commit 03bb6a9b1ed7085794c5f167307273d15c99d3f0.
2020-12-07arm: mvebu: a38x: Configurable USB2 high-speed impedance thresholdJoshua Scott
Hardware testing of a board using the Armada 385 has shown that an impedance threshold setting of 0x7 performs better in an eye-diagram test than with Marvell's recommended value 0x6. As other boards may still perform better with Marvell's reccomended value, a configuration option is added with a default value of 0x6. Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz> Reviewed-by: Stefan Roese <sr@denx.de>
2020-12-07arm: mvebu: puzzle-m801: Add a maintainerLuka Kovacic
Add Luka Perkov to Puzzle-M801 BOARD MAINTAINERS. Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de>
2020-12-06colibri-imx8x: add implementation for board_mem_get_layoutIgor Opaniuk
Add implementation of board_mem_get_layout for overriding the memory layout. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-12-06apalis-imx8x: add implementation for board_mem_get_layoutIgor Opaniuk
Add implementation of board_mem_get_layout for overriding the memory layout. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-12-06apalis-imx8: add implementation for board_mem_get_layoutIgor Opaniuk
Add implementation of board_mem_get_layout for overriding the memory layout. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06imx8: allow overriding memory layoutMarcel Ziswiler
Introduce weak function board_mem_get_layout() which allows overriding the memory layout from board code in runtime, useful for handling different SKU versions. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06doc: board: apalis-imx8x: add documentationIgor Opaniuk
This documents the u-boot build and deployment procedure. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06board: toradex: add apalis-imx8x 2gb wb it v1.1a module supportIgor Opaniuk
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB IT V1.1A System on Module support [1]. Boot log: U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300) CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... OK In: serial@5a070000 Out: serial@5a070000 Err: serial@5a070000 Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A, Serial# 06617018 Net: eth0: ethernet@5b040000 [PRIME] Hit any key to stop autoboot: 0 Functionality wise the following is known to be working: - eMMC and MMC/SD card - Ethernet (*) - GPIOs - I2C Unfortunately, there is no USB functionality for the i.MX 8QXP as of yet. * With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1) ETH PHY encounters bring up problems after reset, this will be fixed soon on SCU FW side. [1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06ARM: dts: fsl-imx8qxp-apalis: add initial device treeIgor Opaniuk
Introduce initial hierarchy of device trees for Apalis iMX8X System on Module. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06imx8m: fix cache setup for dynamic sdram sizeTim Harvey
the mem_map structure containing the size of SDRAM is used in various cache functions in cache_v8.c thus we need to update it with the sdram size the board is configured with as well. Without this the cache functions do not get setup properly and can hang in the case where a board reports more SDRAM than defined in PHYS_SDRAM_SIZE. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2020-12-06verdin-imx8mm: automatic ram size detectionMarcel Ziswiler
Implement board_phys_sdram_size() to automatically detect Verdin iMX8M Mini DualLite 1GB vs. Verdin iMX8M Mini Quad 2GB. Note: This only works if we keep using similar RAM chips! Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06toradex: tdx-cfg-clock: fix i.mx 8m mini interactiveMarcel Ziswiler
Now with them first Verdin iMX8M Mini DualLite modules in for bring-up we got clarity how is_cpu_type() actually behaves. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06verdin-imx8mm: spl: enable pca9450 i2c level translatorMax Krummenacher
Enable PCA9450 i2c level translator, as this is used for the on module ADC. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06verdin-imx8mm: implement hardware version detectionMax Krummenacher
And select the correct devicetree accordingly by setting the variant environment variable. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2020-12-06verdin-imx8mm: spl: switch to pca9450 pmicMax Krummenacher
V1.1A HW switched the PMIC from BD71837 to PCA9450. - Disable combined DVS in PCA9450_BUCK123_DVS. - Increase DDR Voltage to 0.95V as we use a 1.5GHz RAM. - Configure WDOG_B behaviour. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06ARM: dts: imx8mm-verdin: follow changed pmicMax Krummenacher
The used PMIC has been changed from RHOM BD71837 to NXP PCA9450A. Adjust the device tree accordingly. Remove the old ADC node as the ADC has been changed and has no longer a separate power rail. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-06power: pmic: add SPL_DM_PMIC_PCA9450 symbol to KconfigIgor Opaniuk
Add SPL_DM_PMIC_PCA9450 symbol to Kconfig. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-12-06pca9450a: fix i2c addressMax Krummenacher
The I2C address is 0x25, not 0x35. This according to the datasheet and tests with a PCA9450A. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-12-06toradex: tdx-cfg-clock: add new i.mx 8m mini/plus skusMarcel Ziswiler
Add new i.MX 8M Mini/Plus SKUs to ConfigBlock handling: 0058: Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT 0059: Verdin iMX8M Mini Quad 2GB IT 0060: Verdin iMX8M Mini DualLite 1GB WB IT 0061: Verdin iMX8M Plus Quad 2GB Rename existing SKU (use correct one): Verdin iMX8M Nano SoloLite 1GB -> Verdin iMX8M Nano Quad 1GB Wi-Fi Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2020-12-06mmc: fsl_esdhc_imx: optimize the timing settingHaibo Chen
For imx usdhc/esdhc, once set the DDR_EN, enable the DDR mode, the card clock will be divied by 2 automatically by the host. So need to first config the DDR_EN correctly, then update the card clock. This will make sure the actual card clock is as our expected. IC also suggest config the DDR_EN firstly, then config the clock divider. For HS400/HS400ES mode, need to config the strobe dll, this need to based on the correct target clock rate, so need to do this after clock rate is update. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-12-06imx: imx8qm_rom7720_a1: add missing DTS to the MAINTAINERSOliver Graute
add the dts file to the MAINTAINERS entry Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: uboot-imx <uboot-imx@nxp.com>
2020-12-06board: ge: bx50v3: check b850v3 power management watchdogIan Ray
Set `bootcause' from b850v3 power management watchdog status. Boot cause "REVERT" is no longer used, remove it. Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2020-12-06board: ge: reduce VPD EEPROM partition sizeIan Ray
Reduce vital product data size to match the latest specification. Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2020-12-06board: ge: bx50v3: reduce magic numbersSebastian Reichel
Use VPD product ID instead of confidx, so that we can easily reuse the product ID defines and avoid some magic numbers. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2020-12-06board: ge: bx50v3: drop unused pinmux definesSebastian Reichel
Remove pinmux defines, that are no longer used after converting the code to devicetree. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2020-12-06board: ge: bx50v3: correct CONFIG_CMD_NFSIan Ray
Fix typo in NFS command configuration check. Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2020-12-06board: ge: common: vpd: fix nameSebastian Reichel
Commit f692b479f02d changed the VPD partition name from "vpd" to "vpd@0". Fix the VPD reader code to use the new name, so that the VPD code keeps working. Fixes: f692b479f02d ("i2c: eeprom: Use reg property instead of offset and size") Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2020-12-06mmc: fsl_esdhc_imx: add wait_dat0() supportHaibo Chen
Add wait_dat0() support, upper layer will use this callback. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-12-06imx: ahab: fix implicit declaration warningOliver Graute
Fix the following warning: arch/arm/mach-imx/imx8/ahab.c:105:3: warning: implicit declaration of function ‘flush_dcache_range’ [-Wimplicit-function-declaration] flush_dcache_range(s, e); ^~~~~~~~~~~~~~~~~~ Include cpu_func.h header which declares the flush_dcache_range() function. Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: uboot-imx <uboot-imx@nxp.com>
2020-12-06imx: ahab: fix compiler warnings in debugOliver Graute
arch/arm/mach-imx/imx8/ahab.c: In function ‘authenticate_os_container’: arch/arm/mach-imx/imx8/ahab.c:96:9: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 9 has type ‘ulong {aka long unsigned int}’ [-Wformat=] debug("img %d, dst 0x%x, src 0x%x, size 0x%x\n", Fix those by using "%lu" specified. Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: uboot-imx <uboot-imx@nxp.com>
2020-12-06imx: ahab: Fix compiler warnings in printfOliver Graute
arch/arm/mach-imx/imx8/ahab.c:110:63: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘u64 {aka long long unsigned int}’ [-Wformat=] Fix those by using %llx Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: uboot-imx <uboot-imx@nxp.com>
2020-12-06imx: clk: added IPG Clock for I2C on imx8qmOliver Graute
This patch fixes this clk issue on I2C on imx8qm => i2c bus Bus 3: i2c@5a830000 => i2c dev 3 Setting bus to 3 Failed to enable ipg clk Failure changing bus number (-524) Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-11 04:25:48 +0000