aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-04-13board: ge: bx50v3: Enable CONFIG_DM_MMCIan Ray
Use MMC device model, and remove USDHC pin configuration code since the pinctrl driver is used. Signed-off-by: Ian Ray <ian.ray@ge.com>
2019-04-13board: ge: bx50v3: Enable CONFIG_DMIan Ray
Add simplified, generalised, bx50v3 device tree and enable CONFIG_DM. Signed-off-by: Ian Ray <ian.ray@ge.com>
2019-04-13pcm052: bk4: Add board_phy_config() for BK4 to setup ksz8081 phyLukasz Majewski
BK4 requires setup of 50MHz reference clock for its KSZ8081 PHY devices. Signed-off-by: Lukasz Majewski <lukma@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-13pcm052: mac: Provide board specific imx_get_mac_from_fuse() functionLukasz Majewski
This commit introduces the board specific function to read fused mac address. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: board: Add code to setup LED default statesLukasz Majewski
As one has moved to DM based LEDs, this code is required to setup the default state. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: bk4: sdcard: Add support for SD card booting/recoveryLukasz Majewski
This code allows reusing the default u-boot as in the late board init, the default envs are restored and proper recovery scripts executed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13config: bk4: Update u-boot envs to support NOR memories initial setupLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13config: bk4: Update u-boot script to support recovery via SD cardLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: board: Remove in-board setup code (it is now replaced by DM setup)Lukasz Majewski
This commit cleans up the pcm052.c file to remove dead code after moving to DTS and DM. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13config: bk4: Update include/configs/bk4r1.h fileLukasz Majewski
The BK4's config file has changed since its initial posting to main line. This commit reflects those changes. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13config: pcm052: Use SZ_X{MK} from linux/sizes.h for include/configs/pcm052.hLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13defconfig: bk4/pcm052: Update bk4r1|pcm052_defconfig to support DM/DTLukasz Majewski
This commit updates BK4's and PCM052's config files to support as much as possible device tree and model in u-boot. Moreover, remove CONFIG_* from pcm052.h (as those are now in bk4|pcm052_defconfig) Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13ARM: DTS: Provide vf610-bk4r1-u-boot.dtsi for U-Boot specific propertiesLukasz Majewski
This commit brings a separate file in which the U-Boot specific properties (like 'dm-pre-reloc') are provided. Such approach allows easy sync with upstream Linux kernel in the future. Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-04-13ARM: DTS: Update pcm052 based dts files (bk4r1/pcm052)Lukasz Majewski
This commit provides update and renames the bk4r1.dts to vf610-bk4r1.dts file with more on SoC HW description. The pcm052.dts has been renamed to vf610-pcm052.dts as well. Moreover, a new vf610-pcm052.drsi file has been introduced to reuse the common code between devices based on Phytec's pcm052 modules. Ported from Linux kernel - v4.20 (tag) Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: board: cosmetic: Add copyright notice to pcm052.cLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13ARM: DTS: vybrid: Update vf.dtsi file to descibe more vf610 hardwareLukasz Majewski
This patch allows moving vf610 based boards to a device tree and model. Ported from Linux kernel - v4.20 (tag) Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Stefan Agner <stefan.agner@toradex.com> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13pcm052: board: vybrid: Update the board name for BK4 deviceLukasz Majewski
This commit provides distinction between PCM052 and BK4. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: board: Remove "m4go" command as it is superseded by "bootaux"Lukasz Majewski
The "m4go" provides exactly the same functionality as the IMX generic "bootaux" command. Remove it to not duplicate the code. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13vybrid: Define the imx_get_mac_from_fuse() as a __weak functionLukasz Majewski
The proposed way of reading fused MAC in the imx_get_mac_from_fuse() may be different for other boards. This commit defines the imx_get_mac_from_fuse() as a weak function to allow board file overriding it with customized function. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: board: Do not enable I2C2 code in the board fileLukasz Majewski
As the I2C2 clock is now enabled in the generic clock code, we can remove this code from a board file. Signed-off-by: Lukasz Majewski <lukma@denx.de> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13vybrid: clock: Provide enable_i2c_clk() function for VybridLukasz Majewski
Provide function to enable I2C clocks for vf610 - in the generic code. This function overrides the default weak function implementation (which only returns 1). Signed-off-by: Lukasz Majewski <lukma@denx.de> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13vybrid: ddr: Extend vf610-pinfunc.h with DDR pads definitionsLukasz Majewski
This patch provides definitions necessary for VF610 DDR pad configurations. Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
2019-04-13net: Kconfig: FEC: Add dependency on VF610Lukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
2019-04-13net: FEC: Add compatible for vybrid (vf610) to reuse fec_mxc.c driverLukasz Majewski
The NXP's FEC driver can be reused on vf610 device (with DM). Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
2019-04-12Merge tag 'u-boot-stm32-20190412' of https://github.com/patrickdelaunay/u-bootTom Rini
stm32 patches for v2019.07-rc1 - Add trusted boot with TF-A for stm32mp1 - stm32mp1 dts files sync'ed with Linux version - add STM32MP1 Discovery boards (DK1 and DK2) - add STMFX gpio expander driver - misc improvement for stm3mp1 supports - rename stpmu1 to stpmic1 (official name) - stm32_qspi: move to exec_op (spi nor driver for stm32 mpu and mcu) - add STM32 FMC2 NAND flash controller driver
2019-04-12Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2019-04-12Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2019-04-12Merge git://git.denx.de/u-boot-marvellTom Rini
- Misc dts files sync'ed with Linux version (Chris) - Orion watchdog fix (Chris) - kwbimage changed to also support Marvell bin_hdr binary (Chris) - Add DM support to enable CONFIG_BLK for sata_mv (Stefan) - Enable BLK on multiple platforms (Stefan) - Misc minor fixes to AXP theadorable board (Stefan) - Correct logic for DM_SCSI + unconverted drivers check (stefan) - Misc changes to kirkwood to enable DM_USB here (Chris) - Change ahci_mvebu to enable usage on A38x (Baruch) - Update the kirkwood entry in git-mailrc (Baruch) - Misc minor improvements (turris, documentation) (Baruch) - Enhance sata_mv to support Kirkwood as well (Michael) - Add wdt command (Michael) - Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG board support (Chris)
2019-04-12Merge branch '2019-04-11-ti-master-imports'Tom Rini
- Improve Keystone 3 SoC support (DMA, TI SCI) - Improve Keystone 2 SoC support (PHY fixes on various platforms) - Improve am335x families (new platforms, more boot mode options in SPL via DM). - General DaVinci, OMAP5 fixes.
2019-04-12mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driverChristophe Kerello
The driver adds the support for the STMicroelectronics FMC2 NAND Controller found on STM32MP SOCs. This patch adds the polling mode, a basic mode that do not need any DMA channels. Only NAND_ECC_HW mode is actually supported. The driver supports a maximum 8k page size. The following ECC strength and step size are currently supported: - nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8) - nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4) - nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC based on Hamming) This patch has been tested on Micron MT29F8G08ABACAH4. Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
2019-04-12dt-bindings: mtd: stm32_fmc2: add STM32 FMC2 NAND controller documentationChristophe Kerello
This patch adds the documentation of the device tree bindings for the STM32 FMC2 NAND controller. Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
2019-04-12spi: stm32_qspi: move to exec_opChristophe Kerello
We are facing issues in the driver since SPI NOR framework has moved on SPI MEM framework, and SPI NAND framework is not running properly with the current driver. To be able to solve issues met on SPI NOR Flashes and to be able to support SPI NAND Flashes, the driver has been reworked. We are now using exec_op ops instead of using xfer ops. Thanks to this rework, the driver has been successfully tested with: - mx66l51235l SPI NOR Flash on stm32f746 SOC - n25q128a SPI NOR Flash on stm32f769 SOC - mx66l51235l SPI NOR Flash on stm32mp1 SOC - mt29f2g01abagd SPI NAND Flash on stm32mp1 SOC Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com> Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
2019-04-12ARM: dts: Add STMFX gpio expander support for stm32mp157c-ev1Patrick Delaunay
Adds alias to set the pincontrol seq id. For STMFX gpio expander, force sequence number after the last bank (GPIOZ) to avoid conflict between STM32MP and STMFX gpio bank sequence number. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12board: stm32mp1: Force pinctrl driver probe in board_init()Patrice Chotard
In order to insure that hog GPIOs are configured early during the boot process, force all pinctrl driver probing in board_init(). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12config: stm32mp15: Enable STMFX supportPatrick Delaunay
Activate PINCTRL_STMFX and needed part for generic pincontrol PINCTRL_FULL, PINCONF. Increase pre-reloc memory for MALLOC (needed for each DM pinconfig node). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driverPatrick Delaunay
This patch adds pinctrl/GPIO driver for STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander. STMFX is an I2C slave controller, offering up to 24 GPIOs. The driver relies on UCLASS_PINCTRL and UCLASS_GPIO. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12ARM: dts: stm32mp1: Add adc nodesPatrice Chotard
Add adc related nodes. These nodes are used to detect the current supplied by USB type-C power in port on DK1 and DK2 boards. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12Board: stm32mp1: Add supply current boot informationPatrice Chotard
For DK1/DK2 boards, check if power supply provides enough current to allow the board to boot correctly. ADC@0 channel 18 and 19 are connected to USB type-C CC1 and CC2 signals. The table below shows the behavior for different range of CC1 or CC2: range | power supply | red led | console message (Volts) | (Amps) | blinks | --------------|--------------|---------|----------------------------------- [2.10 - 1.23[ | 3 | NO | NO [1.23 - 0.66[ | 1.5 | 3 times | WARNING 1.5A power supply detected [0.66 - 0] | 0.5 | 2 times | WARNING 500mA power supply detected If detected current is < 3A, red led is kept ON after blinking. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12board: stm32mp1: Update README filePatrice Chotard
Update README with DK1 and DK2 boards related informations Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12ARM: dts: stm32: Synchronize DT with kernel onePatrice Chotard
This patch synchronizes U-boot DT with kernel one This is based on https://patchwork.kernel.org/cover/10797115/ This patch adds initial support of STM32MP157 discovery boards: - Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1). This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios) and 512MB of DDR3. Several connections are available on this boards: 4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ... - Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2). This board is a "super-set" of stm32mp157a-dk1. A display panel (otm8009a) and Murata wifi/BT combo is added. Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12stpmic1: add NVM update support in fuse commandPatrick Delaunay
Add functions to read/update the non volatile memory of STPMIC1 (8 bytes-register at 0xF8 address) and allow access with fuse command (bank=1, word > 0xF8). For example: STM32MP> fuse read 1 0xf8 8 Reading bank 1: Word 0x000000f8: 000000ee 00000092 000000c0 00000002 Word 0x000000fc: 000000f2 00000080 00000002 00000033 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: dts: activate psci-1.0Patrick Delaunay
Updates the stm32mp157c devicetree to bind the U-Boot PSCI driver need for power off command; TF-A for stm32mp15x supports PSCI 1.0. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add command poweroffPatrick Delaunay
Activate the command poweroff by default for STM32MP1: - with PCSI from TF-A for trusted boot - with PMIC sysreset request for basic boot (SYSRESET_POWER) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12pmic: stpmu1: add power switch off supportPatrick Delaunay
Add sysreset support, and support power switch off request, needed by poweroff command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stpmic1: update register namesPatrick Delaunay
Alignment with STPMIC1 datasheet s/MAIN_CONTROL_REG/MAIN_CR/g s/MASK_RESET_BUCK/BUCKS_MRST_CR/g s/MASK_RESET_LDOS/LDOS_MRST_CR/g s/BUCKX_CTRL_REG/BUCKX_MAIN_CR/g s/VREF_CTRL_REG/REFDDR_MAIN_CR/g s/LDOX_CTRL_REG/LDOX_MAIN_CR/g s/USB_CTRL_REG/BST_SW_CR/g s/STPMIC1_NVM_USER_STATUS_REG/STPMIC1_NVM_SR/g s/STPMIC1_NVM_USER_CONTROL_REG/STPMIC1_NVM_CR/g and update all the associated defines. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12power: rename stpmu1 to official name stpmic1Patrick Delaunay
Alignment with kernel driver name & binding introduced by https://patchwork.kernel.org/cover/10761943/ to use the final marketing name = STPMIC1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12power: stpmu1: rename files to stpmic1Patrick Delaunay
Prepare file modification for kernel alignment and rename driver to stpmic1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12regulator: stpmu1: update buck1 rangePatrick Delaunay
SW impact for Rev 1.2 of STPMIC1 in U-Boot: Buck converters output voltage change for Buck1 => Vdd min 0,725 to max 1,5V instead of 0.6V to 1.35V (see STPMIC1 datasheet / chapter 5.3 Buck converters) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: Replace OTP read by SHADOW readPatrick Delaunay
Replace STM32_BSEC_OTP() by STM32_BSEC_SHADOW() to increase read performance. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: bsec: shadow all the upper OTP (no secure) during bootPatrick Delaunay
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-09-21 05:57:52 +0000