aboutsummaryrefslogtreecommitdiff
path: root/include/linux
AgeCommit message (Collapse)Author
2023-02-10Correct SPL uses of SANDBOX_CLK_CCFSimon Glass
This converts 12 usages of this option to the non-SPL form, since there is no SPL_SANDBOX_CLK_CCF defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-07mtd: Drop unused fsmc_nand driverSimon Glass
This is not used since this commit: 570c3dcfc15 arm: Remove spear600 boards and the rest of SPEAr support Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
2023-02-07mtd: Drop unused fsl_upm driverSimon Glass
This is not used since this commit: 8d1e3cb1400 powerpc: mpc83xx: remove MPC8360ERDK, EMPC8360EMDS support Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-By: Michael Trimarchi <michael@amarulasolutions.com>
2023-01-26mtd: spi-nor: Add support for Infineon s25fs256tTakahiro Kuwano
Infineon S25FS256T is 256Mbit Quad SPI NOR flash. The key features and differences comparing to other Spansion/Cypress flash familes are: - 4-byte address mode by factory default - Quad mode is enabled by factory default - Supports mixture of 128KB and 64KB sectors by OTP configuration (this patch supports uniform 128KB only) Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2023-01-26mtd: spi-nor-core: Make CFRx reg fields genericTakahiro Kuwano
Cypress defines two flavors of configuration registers, volatile and non volatile, and both use the same bit fields. Rename the bitfields in the configuration registers so that they can be used for both flavors. Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org> Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org> Reviewed-by: Dhruva Gole <d-gole@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2023-01-26mtd: spi-nor-core: Consider reserved bits in CFR5 registerTakahiro Kuwano
CFR5[6] is reserved bit and must be always 1. Set it to comply with flash requirements. While fixing SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN definition, stop using magic numbers and describe the missing bit fields in CFR5 register. This is useful for both readability and future possible addition of Octal STR mode support. Fixes: ea9a22f7e79c ("mtd: spi-nor-core: Add support for Cypress Semper flash") Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org> Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org> Reviewed-by: Dhruva Gole <d-gole@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2023-01-18lib: zstd: update to latest Linux zstd 1.5.2Brandon Maier
Update the zstd implementation to match Linux zstd 1.5.2 from commit 2aa14b1ab2. This was motivated by running into decompression corruption issues when trying to uncompress files compressed with newer versions of zstd. zstd users also claim significantly improved decompression times with newer zstd versions which is a side benefit. Original zstd code was copied from Linux commit 2aa14b1ab2 which is a custom-built implementation based on zstd 1.3.1. Linux switched to an implementation that is a copy of the upstream zstd code in Linux commit e0c1b49f5b, this results in a large code diff. However this should make future updates easier along with other benefits[1]. This commit is a straight mirror of the Linux zstd code, except to: - update a few #include that do not translate cleanly - linux/swab.h -> asm/byteorder.h - linux/limits.h -> linux/kernel.h - linux/module.h -> linux/compat.h - remove assert() from debug.h so it doesn't conflict with u-boot's assert() - strip out the compressor code as was done in the previous u-boot zstd - update existing zstd users to the new Linux zstd API - change the #define for MEM_STATIC to use INLINE_KEYWORD for codesize - add a new KConfig option that sets zstd build options to minify code based on zstd's ZSTD_LIB_MINIFY[2]. These changes were tested by booting a zstd 1.5.2 compressed kernel inside a FIT. And the squashfs changes by loading a file from zstd compressed squashfs with sqfsload. buildman was used to compile test other boards and check for binary bloat, as follows: > $ buildman -b zstd2 --boards dh_imx6,m53menlo,mvebu_espressobin-88f3720,sandbox,sandbox64,stm32mp15_dhcom_basic,stm32mp15_dhcor_basic,turris_mox,turris_omnia -sS > Summary of 6 commits for 9 boards (8 threads, 1 job per thread) > 01: Merge branch '2023-01-10-platform-updates' > arm: w+ m53menlo dh_imx6 > 02: lib: zstd: update to latest Linux zstd 1.5.2 > aarch64: (for 2/2 boards) all -3186.0 rodata +920.0 text -4106.0 > arm: (for 5/5 boards) all +1254.4 rodata +940.0 text +314.4 > sandbox: (for 2/2 boards) all -4452.0 data -16.0 rodata +640.0 text -5076.0 [1] https://github.com/torvalds/linux/commit/e0c1b49f5b674cca7b10549c53b3791d0bbc90a8 [2] https://github.com/facebook/zstd/blob/f302ad8811643c428c4e3498e28f53a0578020d3/lib/libzstd.mk#L31 Signed-off-by: Brandon Maier <brandon.maier@collins.com> [trini: Set ret to -EINVAL for the error of "failed to detect compressed" to fix warning, drop ZSTD_SRCSIZEHINT_MAX for non-Linux host tool builds] Signed-off-by: Tom Rini <trini@konsulko.com>
2023-01-08Merge tag 'u-boot-nand-20230108' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-nand-flash into next Pull request for u-boot-nand-20230108 - rawnand: omap_gpmc: driver model support
2023-01-08mtd: rawnand: omap_elm: u-boot driver model supportRoger Quadros
Support u-boot driver model. We still retain support legacy way of doing things if ELM_BASE is defined in <asm/arch/hardware.h> We could completely get rid of that if all platforms defining ELM_BASE get rid of that definition and enable CONFIG_SYS_NAND_SELF_INIT and are verified to work. Signed-off-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Reviewed-by: Tom Rini <trini@konsulko.com> Link: https://lore.kernel.org/all/20221220102203.52398-9-rogerq@kernel.org Link: https://lore.kernel.org/all/CABGWkvrvKiVA_yaDnHJcHEKwc+pEuLdz=i6HQEY0oJQvohCUsw@mail.gmail.com
2023-01-06Merge tag 'u-boot-at91-2023.04-a' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-at91 into next First set of u-boot-at91 features for the 2023.04 cycle: This feature set includes the new DM-based NAND flash driver (old non-DM driver is still kept for backwards compatibility), and the move to DM NAND flash driver for sam9x60ek board. Feature set also includes devicetree alignment for sama7g5 with Linux, devicetree alignment on USB with Linux for all boards (sama5, sam9x60), chip id for sama7g5, minor configs and tweaks.
2022-12-10mtd: nand: drop EXPORT_SYMBOL_GPL for nanddev_erase()Dario Binacchi
This function is only used within this module, so it is no longer necessary to use EXPORT_SYMBOL_GPL(). This patch parallels the work done in the following patch: https://lore.kernel.org/linux-mtd/20221018170205.1733958-1-dario.binacchi@amarulasolutions.com Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Reviewed-By: Michael Trimarchi <michael@amarulasolutions.com> Link: https://lore.kernel.org/all/20221108090719.3631621-1-dario.binacchi@amarulasolutions.com
2022-12-08mfd: syscon: atmel-smc: Add new helpers to ease SMC regs manipulationBalamanikandan Gunasundar
Add helper functions for atmel Static Memory Controller. The functions are required to configure SMC. This file is inherited from the work done by Boris Brezillon for Linux Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
2022-12-08mfd: syscon: Add atmel-matrix registers definitionBalamanikandan Gunasundar
This file is copied from Linux. AT91 SoCs have a memory range reserved for internal bus configuration. Expose those registers so that drivers can make use of the matrix syscon declared in at91 DTs. Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
2022-11-28liteeth: LiteX Ethernet deviceJoel Stanley
LiteX is a soft system-on-chip that targets FPGAs. LiteETH is a basic network device that is commonly used in LiteX designs. Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-11-02list.h: synchronize hlist_for_each_entry* iterators with linuxRasmus Villemoes
All the way back in 2013, the linux kernel updated the four hlist_for_each_entry* iterators to require one less auxiliary variable: commit b67bfe0d42cac56c512dd5da4b1b347a23f4b70a Author: Sasha Levin <sasha.levin@oracle.com> Date: Wed Feb 27 17:06:00 2013 -0800 hlist: drop the node parameter from iterators Currently, there is only one "user" of any of these, namely in fs/ubifs/super.c, but that actually uses the "new-style" form, and is (obviously, or it wouldn't have built) inside #ifndef __UBOOT__. Before adding actual users of these, import the version as of linux v6.1-rc1, including the hlist_entry_safe() helper used by the new versions. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Tim Harvey <tharvey@gateworks.com> # imx8mm-venice-*
2022-10-26memory: Add TI GPMC driverRoger Quadros
The GPMC is a unified memory controller dedicated for interfacing with external memory devices like - Asynchronous SRAM-like memories and ASICs - Asynchronous, synchronous, and page mode burst NOR flash - NAND flash - Pseudo-SRAM devices This driver will take care of setting up the GPMC based on the settings specified in the Device tree and then probe its children. Signed-off-by: Roger Quadros <rogerq@kernel.org>
2022-10-23mtd: spi-nor-core: Track flash's internal address modeTakahiro Kuwano
The nor->addr_width tracks number of address bytes used in read/program/erase ops and eventually set to 4 for >16MB chips, regardless of flash's internal address mode. For Infineon SEMPER flash's, we use Read/Write Any Register commands for configuration and status check. These commands take 3- or 4-byte address depending on flash's internal address mode. Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2022-10-09mtd: Update the function name to 'rfree'Fabio Estevam
Since commit 8d38a8459b0d ("mtd: Rename free() to rfree()") the function has been renamed to rfree(), so update the description inside the mtd_oob_region structure as well. Fixes: 8d38a8459b0d ("mtd: Rename free() to rfree()") Reported-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu> Signed-off-by: Fabio Estevam <festevam@denx.de> Acked-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-09-18cyclic: Use schedule() instead of WATCHDOG_RESET()Stefan Roese
Globally replace all occurances of WATCHDOG_RESET() with schedule(), which handles the HW_WATCHDOG functionality and the cyclic infrastructure. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
2022-09-13mtd: spi-nor: Use spi-mem dirmap APIChin-Ting Kuo
This adds support for the dirmap API to the spi-nor subsystem, as introduced in Linux commit df5c21002cf4 ("mtd: spi-nor: use spi-mem dirmap API"). This patch is synchronize from the following patch https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-4-seanga2@gmail.com/ The corresponding Linux kernel SHA1 is df5c21002cf4. Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com> Signed-off-by: Sean Anderson <seanga2@gmail.com> Acked-by: Pratyush Yadav <p.yadav@ti.com>
2022-08-24Merge commit 'ac30d240dbb520d0980f0687630feb702a14f51a' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-nand-flash into next Re-sync again on some linux part, add some fixes for fsl_elbc from Pali and switch imx8mn bsh to use nand base ident For nand subsystem tested on: - imx8mn Macronix MX30LF4G18AC - P2020 based board Turris 1.1 for fsl_elbc
2022-08-23arm: mvebu: mbus: Fix mbus driver to work also after U-Boot relocationPali Rohár
mbus driver is initialized from arch_cpu_init() callback which is called before relocation. This driver stores lot of functions and structure pointers into global variables, so it is data position dependent. Therefore after relocations all pointers are invalid and driver does not work anymore as all pointers referes to the old memory, which overlaps with CONFIG_SYS_LOAD_ADDR and ${loadaddr}. For example U-Boot fuse command crashes if loadaddr memory is cleared or rewritten by some image loaded by U-Boot load command. mw.w ${loadaddr} 0x0 10000 fuse read 0 1 2 Fix this issue by removing of all mbus global variables in which are stored pointers to structures or functions which changes during relocation. And replace it by direct function calls (not via pointers). With this change fuse command finally works. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Stefan Roese <sr@denx.de>
2022-08-22mtd: nand: Rename nand_get_flash_type() into nand_detect()Michael Trimarchi
Upstream linux commit 7bb427990ee364. Rename the function to match this new behavior. NOTE: fix nand_detect/nand_get_flash_type parameters in mxs_nand_spl. This code seems never executed by any board as alternative for nand detect Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-08-22mtd: nand: change return type of nand_get_flash_type() to intMichael Trimarchi
Upstream linux commit 4722c0e958e636. The returned "type" is never used in nand_scan_ident() and spl code Make nand_get_flash_type() simply return an integer value in order to avoid unnecessary ERR_PTR/PTR_ERR dance. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-08-22mtd: nand: Rename the nand_manufacturers structMichael Trimarchi
Upstream linux commit 8cfb9ab68f9070. Drop the 's' at the end of nand_manufacturers since the struct is actually describing a single manufacturer, not a manufacturer table. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-08-20powerpc: remove support for kmtergr1 and MPC8309Holger Brunck
The kmtegr1 board is out of maintenance and can be removed. As it is the only board in the tree using MPC8309 the support for this CPU is dropped completely. Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
2022-07-22mtd: nand: Move Macronix specific initialization in nand_macronix.cMichael Trimarchi
Upstream linux commit 3b5206f4be9b65. Move Macronix specific initialization logic into nand_macronix.c. This is part of the "separate vendor specific code from core" cleanup process. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-07-22mtd: nand: Move AMD/Spansion specific init/detection logic in nand_amd.cMichael Trimarchi
Upstream linux commit 229204da53b31d. Move AMD/Spansion specific initialization/detection logic into nand_amd.c. This is part of the "separate vendor specific code from core" cleanup process. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-07-22mtd: nand: Move Micron specific init logic in nand_micron.cMichael Trimarchi
Upstream linux commit 10d4e75c36f6c1. Move Micron specific initialization logic into nand_micron.c. This is part of the "separate vendor specific code from core" cleanup process. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-07-22mtd: nand: Move Toshiba specific init/detection logic in nand_toshiba.cMichael Trimarchi
Upstream linux commit 9b2d61f80b060c. Move Toshiba specific initialization and detection logic into nand_toshiba.c. This is part of the "separate vendor specific code from core" cleanup process. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-07-22mtd: nand: Move Hynix specific init/detection logic in nand_hynix.cMichael Trimarchi
Upstream linux commit 01389b6bd2f4f7. Move Hynix specific initialization and detection logic into nand_hynix.c. This is part of the "separate vendor specific code from core" cleanup process. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-07-22mtd: nand: Move Samsung specific init/detection logic in nand_samsung.cMichael Trimarchi
Upstream linux commit c51d0ac59f2420. Move Samsung specific initialization and detection logic into nand_samsung.c. This is part of the "separate vendor specific code from core" cleanup process. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-07-22mtd: nand: Export symbol nand_decode_ext_idMichael Trimarchi
In preparation of moving specific nand support that are not jedec or onfi Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-07-22mtd: nand: Get rid of mtd variable in function callsMichael Trimarchi
chip points to mtd. Passing chip is enough to have a reference to mtd when is necessary Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-07-22mtd: nand: Add manufacturer specific initialization/detection stepsMichael Trimarchi
Upstream linux commit abbe26d144ec22. A lot of NANDs are implementing generic features in a non-generic way, or are providing advanced auto-detection logic where the NAND ID bytes meaning changes with the NAND generation. Providing this vendor specific initialization step will allow us to get rid of full-id entries in the nand_ids table or all the vendor specific cases added over the time in the generic NAND ID decoding logic. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-07-22mtd: nand: Store nand ID in struct nand_chipMichael Trimarchi
Upstream linux commit 7f501f0a72036d. Store the NAND ID in struct nand_chip to avoid passing id_data and id_len as function parameters. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-07-18mtd: spi: Convert is_locked callback to is_unlockedJan Kiszka
There was no user of this callback after 5b66fdb29dc3 anymore, and its semantic as now inconsistent between stm and sst26. What we need for the upcoming new usecase is a "completely unlocked" semantic. So consolidate over this. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2022-07-18mtd: spi-nor: Parse SFDP SCCR MapJaimeLiao
Parse SCCR 22nd dword and check DTR Octal Mode Enable Volatile bit for Octal DTR enable Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2022-07-18mtd: spi-nor: add support for Macronix Octal flashJaimeLiao
Follow patch <f6adec1af4b2f5d3012480c6cdce7743b74a6156> (Allow using Micron mt35xu512aba in Octal DTR mode). Enable Octal DTR mode with 20 dummy cycles to allow running at the maximum supported frequency for adding Macronix flash in Octal DTR mode. -https://www.mxic.com.tw/Lists/Datasheet/Attachments/7841/MX25LM51245G,%203V,%20512Mb,%20v1.1.pdf Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2022-07-12usb: common: move urb code to commonRui Miguel Silva
Move urb code from musb only use to a more common scope, so other drivers in the future can use the handling of urb in usb. Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
2022-06-28usb: xhci-fsl: Remove non-DM codeTom Rini
The deadline for DM_USB migration has passed and all users have been migrated. Remove now unused code. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-23firmware: psci: bind arm smccc features when discoveredEtienne Carriere
Use PSCI device to query Arm SMCCC v1.1 support from secure monitor and if so, bind drivers for the SMCCC features that monitor supports. Drivers willing to be bound from Arm SMCCC features discovery can use macro ARM_SMCCC_FEATURE_DRIVER() to register to smccc feature discovery, providing target driver name and a callback function that returns whether or not the SMCCC feature is supported by the system. Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
2022-06-23smccc: define generic IDs for feature discoveryEtienne Carriere
Defines function IDs ARM_SMCCC_ARCH_FEATURES used to query SMCCC feature support, applicable from Arm SMCCC v1.1 specification. Defines macro ARM_SMCCC_RET_NOT_SUPPORTED as generic return identifier for when a SMCCC feature is not supported. Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
2022-06-17stm32mp1: fix reference for STMicroelectronicsPatrick Delaunay
Replace reference to the correct name STMicroelectronics Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-05-20usb: xhci-dwc3: Support role switch default roleMark Kettenis
When the device tree indicates support for role switching through the "usb-role-switch" property, take the "role-switch-default-mode" property into account when deciding which role to put the controller into. This makes USB devices work on Apple M1 systems where the device tree may include a "dr_mode" property that is set to "otg", but where we need to put the controller into "host" mode to see devices connected to the type-C ports. Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
2022-05-05lib/date: Make rtc_mktime and mktime64 Y2038-readyJan Kiszka
We currently overflow due to wrong types used internally in rtc_mktime, on all platforms, and we return a too small type on 32-bit. One consumer that directly benefits from this is mktime64. Many others may still store the result in a wrong type. While at it, drop the redundant cast of mon in rtc_mktime (obsoleted by 714209832db1). Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2022-05-02Introduce Verifying Program Loader (VPL)Simon Glass
Add support for VPL, a new phase of U-Boot. This runs after TPL. It is responsible for selecting which SPL binary to run, based on a verified-boot process. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-04-21crc16: Rename fs/ubifs/crc16.h to include/linux/crc16.hPali Rohár
File fs/ubifs/crc16.h is standard linux's crc16.h include file. So move it from fs/ubifs to include/linux where are also other linux include files. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-04-13Merge tag 'u-boot-imx-20220413' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20220413 i.MX patches for 2022.07 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/11710
2022-04-12iopoll: Extend read_poll_timeout macro to support variable parametersAriel D'Alessandro
This macro currently supports only one parameter. Based on Linux iopoll, let's extend read_poll_timeout common API to allow multiple variable parameters. Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-15 04:54:20 +0000