1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2013-2014 Synopsys, Inc. All rights reserved.
*/
#include <asm-offsets.h>
#include <config.h>
#include <linux/linkage.h>
#include <asm/arcregs.h>
ENTRY(_start)
/* Setup interrupt vector base that matches "__text_start" */
sr __ivt_start, [ARC_AUX_INTR_VEC_BASE]
; Disable/enable I-cache according to configuration
lr r5, [ARC_BCR_IC_BUILD]
breq r5, 0, 1f ; I$ doesn't exist
lr r5, [ARC_AUX_IC_CTRL]
#if !CONFIG_IS_ENABLED(SYS_ICACHE_OFF)
bclr r5, r5, 0 ; 0 - Enable, 1 is Disable
#else
bset r5, r5, 0 ; I$ exists, but is not used
#endif
sr r5, [ARC_AUX_IC_CTRL]
mov r5, 1
sr r5, [ARC_AUX_IC_IVIC]
; As per ARC HS databook (see chapter 5.3.3.2)
; it is required to add 3 NOPs after each write to IC_IVIC.
nop
nop
nop
1:
; Disable/enable D-cache according to configuration
lr r5, [ARC_BCR_DC_BUILD]
breq r5, 0, 1f ; D$ doesn't exist
lr r5, [ARC_AUX_DC_CTRL]
bclr r5, r5, 6 ; Invalidate (discard w/o wback)
#if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF)
bclr r5, r5, 0 ; Enable (+Inv)
#else
bset r5, r5, 0 ; Disable (+Inv)
#endif
sr r5, [ARC_AUX_DC_CTRL]
mov r5, 1
sr r5, [ARC_AUX_DC_IVDC]
1:
#ifdef CONFIG_ISA_ARCV2
; Disable System-Level Cache (SLC)
lr r5, [ARC_BCR_SLC]
breq r5, 0, 1f ; SLC doesn't exist
lr r5, [ARC_AUX_SLC_CTRL]
bclr r5, r5, 6 ; Invalidate (discard w/o wback)
bclr r5, r5, 0 ; Enable (+Inv)
sr r5, [ARC_AUX_SLC_CTRL]
1:
#endif
#ifdef CONFIG_ISA_ARCV2
; In case of DSP extension presence in HW some instructions
; (related to integer multiply, multiply-accumulate, and divide
; operation) executes on this DSP execution unit. So their
; execution will depend on dsp configuration register (DSP_CTRL)
; As we want these instructions to execute the same way regardless
; of DSP presence we need to set DSP_CTRL properly.
lr r5, [ARC_AUX_DSP_BUILD]
bmsk r5, r5, 7
breq r5, 0, 1f
mov r5, 0
sr r5, [ARC_AUX_DSP_CTRL]
1:
#endif
#ifdef __ARC_UNALIGNED__
/*
* Enable handling of unaligned access in the CPU as by default
* this HW feature is disabled while GCC starting from 8.1.0
* unconditionally uses it for ARC HS cores.
*/
flag 1 << STATUS_AD_BIT
#endif
/* Establish C runtime stack and frame */
mov %sp, CONFIG_SYS_INIT_SP_ADDR
mov %fp, %sp
/* Allocate reserved area from current top of stack */
mov %r0, %sp
bl board_init_f_alloc_reserve
/* Set stack below reserved area, adjust frame pointer accordingly */
mov %sp, %r0
mov %fp, %sp
/* Initialize reserved area - note: r0 already contains address */
bl board_init_f_init_reserve
#ifdef CONFIG_DEBUG_UART
/* Earliest point to set up early debug uart */
bl debug_uart_init
#endif
/* Zero the one and only argument of "board_init_f" */
mov_s %r0, 0
bl board_init_f
/* We only get here if relocation is disabled by GD_FLG_SKIP_RELOC */
/* Make sure we don't lose GD overwritten by zero new GD */
mov %r0, %r25
mov %r1, 0
bl board_init_r
ENDPROC(_start)
/*
* void board_init_f_r_trampoline(stack-pointer address)
*
* This "function" does not return, instead it continues in RAM
* after relocating the monitor code.
*
* r0 = new stack-pointer
*/
ENTRY(board_init_f_r_trampoline)
/* Set up the stack- and frame-pointers */
mov %sp, %r0
mov %fp, %sp
/* Update position of intterupt vector table */
lr %r0, [ARC_AUX_INTR_VEC_BASE]
ld %r1, [%r25, GD_RELOC_OFF]
add %r0, %r0, %r1
sr %r0, [ARC_AUX_INTR_VEC_BASE]
/* Re-enter U-Boot by calling board_init_f_r */
j board_init_f_r
ENDPROC(board_init_f_r_trampoline)
|
