1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
|
// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2836.dtsi"
#include "bcm2836-rpi.dtsi"
#include "bcm283x-rpi-smsc9514.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
model = "Raspberry Pi 2 Model B";
memory@0 {
reg = <0 0x40000000>;
};
leds {
act {
gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
pwr {
label = "PWR";
gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
default-state = "keep";
linux,default-trigger = "default-on";
};
};
};
&gpio {
/*
* Taken from rpi_SCH_2b_1p2_reduced.pdf and
* the official GPU firmware DT blob.
*
* Legend:
* "NC" = not connected (no rail from the SoC)
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "ID_SDA",
"ID_SCL",
"SDA1",
"SCL1",
"GPIO_GCLK",
"GPIO5",
"GPIO6",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"GPIO12",
"GPIO13",
/* Serial port */
"TXD0",
"RXD0",
"GPIO16",
"GPIO17",
"GPIO18",
"GPIO19",
"GPIO20",
"GPIO21",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"GPIO26",
"GPIO27",
"SDA0",
"SCL0",
"", /* GPIO30 */
"LAN_RUN",
"CAM_GPIO1",
"", /* GPIO33 */
"", /* GPIO34 */
"PWR_LOW_N",
"", /* GPIO36 */
"", /* GPIO37 */
"USB_LIMIT",
"", /* GPIO39 */
"PWM0_OUT",
"CAM_GPIO0",
"SMPS_SCL",
"SMPS_SDA",
"ETHCLK",
"PWM1_OUT",
"HDMI_HPD_N",
"STATUS_LED",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
/* I2S interface */
i2s_alt0: i2s_alt0 {
brcm,pins = <18 19 20 21>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
};
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};
|
