path: root/arch/arm/mach-k3/am625_init.c

// SPDX-License-Identifier: GPL-2.0
/*
 * AM625: SoC specific initialization
 *
 * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
 *	Suman Anna <s-anna@ti.com>
 */

#include <spl.h>
#include <asm/io.h>
#include <asm/arch/hardware.h>
#include "sysfw-loader.h"
#include "common.h"
#include <dm.h>
#include <dm/uclass-internal.h>
#include <dm/pinctrl.h>
#include <dm/ofnode.h>

#define RTC_BASE_ADDRESS		0x2b1f0000
#define REG_K3RTC_S_CNT_LSW		(RTC_BASE_ADDRESS + 0x18)
#define REG_K3RTC_KICK0			(RTC_BASE_ADDRESS + 0x70)
#define REG_K3RTC_KICK1			(RTC_BASE_ADDRESS + 0x74)

/* Magic values for lock/unlock */
#define K3RTC_KICK0_UNLOCK_VALUE	0x83e70b13
#define K3RTC_KICK1_UNLOCK_VALUE	0x95a4f1e0

/* TISCI DEV ID for A53 Clock */
#define AM62X_DEV_A53SS0_CORE_0_DEV_ID 135

/*
 * This uninitialized global variable would normal end up in the .bss section,
 * but the .bss is cleared between writing and reading this variable, so move
 * it to the .data section.
 */
u32 bootindex __section(".data");
static struct rom_extended_boot_data bootdata __section(".data");

static void store_boot_info_from_rom(void)
{
	bootindex = *(u32 *)(CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX);
	memcpy(&bootdata, (uintptr_t *)ROM_EXTENDED_BOOT_DATA_INFO,
	       sizeof(struct rom_extended_boot_data));
}

static void ctrl_mmr_unlock(void)
{
	/* Unlock all WKUP_CTRL_MMR0 module registers */
	mmr_unlock(WKUP_CTRL_MMR0_BASE, 0);
	mmr_unlock(WKUP_CTRL_MMR0_BASE, 1);
	mmr_unlock(WKUP_CTRL_MMR0_BASE, 2);
	mmr_unlock(WKUP_CTRL_MMR0_BASE, 3);
	mmr_unlock(WKUP_CTRL_MMR0_BASE, 4);
	mmr_unlock(WKUP_CTRL_MMR0_BASE, 5);
	mmr_unlock(WKUP_CTRL_MMR0_BASE, 6);
	mmr_unlock(WKUP_CTRL_MMR0_BASE, 7);

	/* Unlock all CTRL_MMR0 module registers */
	mmr_unlock(CTRL_MMR0_BASE, 0);
	mmr_unlock(CTRL_MMR0_BASE, 1);
	mmr_unlock(CTRL_MMR0_BASE, 2);
	mmr_unlock(CTRL_MMR0_BASE, 4);
	mmr_unlock(CTRL_MMR0_BASE, 6);

	/* Unlock all MCU_CTRL_MMR0 module registers */
	mmr_unlock(MCU_CTRL_MMR0_BASE, 0);
	mmr_unlock(MCU_CTRL_MMR0_BASE, 1);
	mmr_unlock(MCU_CTRL_MMR0_BASE, 2);
	mmr_unlock(MCU_CTRL_MMR0_BASE, 3);
	mmr_unlock(MCU_CTRL_MMR0_BASE, 4);
	mmr_unlock(MCU_CTRL_MMR0_BASE, 6);

	/* Unlock PADCFG_CTRL_MMR padconf registers */
	mmr_unlock(PADCFG_MMR0_BASE, 1);
	mmr_unlock(PADCFG_MMR1_BASE, 1);
}

static __maybe_unused void enable_mcu_esm_reset(void)
{
	/* Set CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RST_EN_Z  to '0' (low active) */
	u32 stat = readl(CTRLMMR_MCU_RST_CTRL);

	stat &= RST_CTRL_ESM_ERROR_RST_EN_Z_MASK;
	writel(stat, CTRLMMR_MCU_RST_CTRL);
}

/*
 * RTC Erratum i2327 Workaround for Silicon Revision 1
 *
 * Due to a bug in initial synchronization out of cold power on,
 * IRQ status can get locked infinitely if we do not unlock RTC
 *
 * This workaround *must* be applied within 1 second of power on,
 * So, this is closest point to be able to guarantee the max
 * timing.
 *
 * https://www.ti.com/lit/er/sprz487c/sprz487c.pdf
 */
static __maybe_unused void rtc_erratumi2327_init(void)
{
	u32 counter;

	/*
	 * If counter has gone past 1, nothing we can do, leave
	 * system locked! This is the only way we know if RTC
	 * can be used for all practical purposes.
	 */
	counter = readl(REG_K3RTC_S_CNT_LSW);
	if (counter > 1)
		return;
	/*
	 * Need to set this up at the very start
	 * MUST BE DONE under 1 second of boot.
	 */
	writel(K3RTC_KICK0_UNLOCK_VALUE, REG_K3RTC_KICK0);
	writel(K3RTC_KICK1_UNLOCK_VALUE, REG_K3RTC_KICK1);
}

#if CONFIG_IS_ENABLED(OF_CONTROL)
static int get_a53_cpu_clock_index(ofnode node)
{
	int count, i;
	struct ofnode_phandle_args *args;
	ofnode clknode;

	clknode = ofnode_path("/bus@f0000/system-controller@44043000/clock-controller");
	if (!ofnode_valid(clknode))
		return -1;

	count = ofnode_count_phandle_with_args(node,  "assigned-clocks", "#clock-cells", 0);

	for (i  = 0; i < count; i++) {
		if (!ofnode_parse_phandle_with_args(node, "assigned-clocks",
						    "#clock-cells", 0, i, args)) {
			if (ofnode_equal(clknode, args->node) &&
			    args->args[0] == AM62X_DEV_A53SS0_CORE_0_DEV_ID)
				return i;
		}
	}

	return -1;
}

static void fixup_a53_cpu_freq_by_speed_grade(void)
{
	int index, size;
	u32 *rates;
	ofnode node;

	node =  ofnode_path("/a53@0");
	if (!ofnode_valid(node))
		return;

	rates = fdt_getprop_w(ofnode_to_fdt(node), ofnode_to_offset(node),
			      "assigned-clock-rates", &size);

	index = get_a53_cpu_clock_index(node);

	if (!rates || index < 0 || index >= (size / sizeof(u32))) {
		printf("Wrong A53 assigned-clocks configuration\n");
		return;
	}

	rates[index] = cpu_to_fdt32(k3_get_a53_max_frequency());

	printf("Changed A53 CPU frequency to %dHz (%c grade) in DT\n",
	       k3_get_a53_max_frequency(), k3_get_speed_grade());
}
#else
static void fixup_a53_cpu_freq_by_speed_grade(void)
{
}
#endif

void board_init_f(ulong dummy)
{
	struct udevice *dev;
	int ret;

	if (IS_ENABLED(CONFIG_CPU_V7R)) {
		setup_k3_mpu_regions();
		rtc_erratumi2327_init();
	}

	/*
	 * Cannot delay this further as there is a chance that
	 * K3_BOOT_PARAM_TABLE_INDEX can be over written by SPL MALLOC section.
	 */
	store_boot_info_from_rom();

	ctrl_mmr_unlock();

	/* Init DM early */
	spl_early_init();

	/*
	 * Process pinctrl for the serial0 and serial3, aka WKUP_UART0 and
	 * MAIN_UART1 modules and continue regardless of the result of pinctrl.
	 * Do this without probing the device, but instead by searching the
	 * device that would request the given sequence number if probed. The
	 * UARTs will be used by the DM firmware and TIFS firmware images
	 * respectively and the firmware depend on SPL to initialize the pin
	 * settings.
	 */
	ret = uclass_find_device_by_seq(UCLASS_SERIAL, 0, &dev);
	if (!ret)
		pinctrl_select_state(dev, "default");

	ret = uclass_find_device_by_seq(UCLASS_SERIAL, 3, &dev);
	if (!ret)
		pinctrl_select_state(dev, "default");

	preloader_console_init();

	/*
	 * Allow establishing an early console as required for example when
	 * doing a UART-based boot. Note that this console may not "survive"
	 * through a SYSFW PM-init step and will need a re-init in some way
	 * due to changing module clock frequencies.
	 */
	if (IS_ENABLED(CONFIG_K3_EARLY_CONS))
		early_console_init();

	/*
	 * Configure and start up system controller firmware. Provide
	 * the U-Boot console init function to the SYSFW post-PM configuration
	 * callback hook, effectively switching on (or over) the console
	 * output.
	 */
	if (IS_ENABLED(CONFIG_K3_LOAD_SYSFW)) {
		ret = is_rom_loaded_sysfw(&bootdata);
		if (!ret)
			panic("ROM has not loaded TIFS firmware\n");

		k3_sysfw_loader(true, NULL, NULL);
	}

	/*
	 * Relocate boot information to OCRAM (after TIFS has opend this
	 * region for us) so the next bootloader stages can keep access to
	 * primary vs backup bootmodes.
	 */
	if (IS_ENABLED(CONFIG_CPU_V7R))
		writel(bootindex, K3_BOOT_PARAM_TABLE_INDEX_OCRAM);

	/*
	 * Force probe of clk_k3 driver here to ensure basic default clock
	 * configuration is always done.
	 */
	if (IS_ENABLED(CONFIG_SPL_CLK_K3)) {
		ret = uclass_get_device_by_driver(UCLASS_CLK,
						  DM_DRIVER_GET(ti_clk),
						  &dev);
		if (ret)
			printf("Failed to initialize clk-k3!\n");
	}

	/* Output System Firmware version info */
	k3_sysfw_print_ver();

	if (IS_ENABLED(CONFIG_ESM_K3)) {
		/* Probe/configure ESM0 */
		ret = uclass_get_device_by_name(UCLASS_MISC, "esm@420000", &dev);
		if (ret)
			printf("esm main init failed: %d\n", ret);

		/* Probe/configure MCUESM */
		ret = uclass_get_device_by_name(UCLASS_MISC, "esm@4100000", &dev);
		if (ret)
			printf("esm mcu init failed: %d\n", ret);

		enable_mcu_esm_reset();
	}

	if (IS_ENABLED(CONFIG_K3_AM64_DDRSS)) {
		ret = uclass_get_device(UCLASS_RAM, 0, &dev);
		if (ret)
			panic("DRAM init failed: %d\n", ret);
	}
	spl_enable_cache();

	fixup_a53_cpu_freq_by_speed_grade();
}

u32 spl_mmc_boot_mode(struct mmc *mmc, const u32 boot_device)
{
	u32 devstat = readl(CTRLMMR_MAIN_DEVSTAT);
	u32 bootmode = (devstat & MAIN_DEVSTAT_PRIMARY_BOOTMODE_MASK) >>
				MAIN_DEVSTAT_PRIMARY_BOOTMODE_SHIFT;
	u32 bootmode_cfg = (devstat & MAIN_DEVSTAT_PRIMARY_BOOTMODE_CFG_MASK) >>
			    MAIN_DEVSTAT_PRIMARY_BOOTMODE_CFG_SHIFT;

	switch (bootmode) {
	case BOOT_DEVICE_EMMC:
		if (IS_ENABLED(CONFIG_SUPPORT_EMMC_BOOT))
			return MMCSD_MODE_EMMCBOOT;
		if (IS_ENABLED(CONFIG_SPL_FS_FAT) || IS_ENABLED(CONFIG_SPL_FS_EXT4))
			return MMCSD_MODE_FS;
		return MMCSD_MODE_EMMCBOOT;
	case BOOT_DEVICE_MMC:
		if (bootmode_cfg & MAIN_DEVSTAT_PRIMARY_MMC_FS_RAW_MASK)
			return MMCSD_MODE_RAW;
	default:
		return MMCSD_MODE_FS;
	}
}

u32 spl_boot_device(void)
{
	return get_boot_device();
}