blob: 974b0be175fe9ed481a036d711617c9c1d33bab8 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
|
How to use and build U-Boot on mx6sabresd
-----------------------------------------
The following methods can be used for booting mx6sabresd boards:
1. Booting from SD card
2. Booting from eMMC
3. Booting via Falcon mode (SPL launches the kernel directly)
1. Booting from SD card via SPL
-------------------------------
mx6sabresd_defconfig target supports mx6q/mx6dl/mx6qp sabresd variants.
In order to build it:
$ make mx6sabresd_defconfig
$ make
This will generate the SPL and u-boot-dtb.img binaries.
- Flash the SPL binary into the SD card:
$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 conv=notrunc && sync
- Flash the u-boot-dtb.img binary into the SD card:
$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 conv=notrunc && sync
2. Booting from eMMC
--------------------
$ make mx6sabresd_defconfig
$ make
This will generate the SPL and u-boot-dtb.img binaries.
- Boot first from SD card as shown in the previous section
In U-boot change the eMMC partition config:
=> mmc partconf 2 1 0 0
Mount the eMMC in the host PC:
=> ums 0 mmc 2
- Flash SPL and u-boot-dtb.img binaries into the eMMC:
$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 conv=notrunc && sync
$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 conv=notrunc && sync
Set SW6 to eMMC 8-bit boot: 11010110
3. Booting via Falcon mode
--------------------------
$ make mx6sabresd_defconfig
$ make
This will generate the SPL image called SPL and the u-boot-dtb.img.
- Flash the SPL image into the SD card:
$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 oflag=sync status=none conv=notrunc && sync
- Flash the u-boot-dtb.img image into the SD card:
$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 oflag=sync status=none conv=notrunc && sync
Create a partition for root file system and extract it there:
$ sudo tar xvf rootfs.tar.gz -C /media/root
The SD card must have enough space for raw "args" and "kernel".
To configure Falcon mode for the first time, on U-Boot do the following commands:
- Setup the IP server:
# setenv serverip <server_ip_address>
- Download dtb file:
# dhcp ${fdt_addr} imx6q-sabresd.dtb
- Download kernel image:
# dhcp ${loadaddr} uImage
- Write kernel at 2MB offset:
# mmc write ${loadaddr} 0x1000 0x4000
- Setup kernel bootargs:
# setenv bootargs "console=ttymxc0,115200 root=/dev/mmcblk1p1 rootfstype=ext4 rootwait quiet rw"
- Prepare args:
# spl export fdt ${loadaddr} - ${fdt_addr}
- Write args 1MB data (0x800 sectors) to 1MB offset (0x800 sectors)
# mmc write 18000000 0x800 0x800
- Press KEY_VOL_UP key, power up the board and then SPL binary will
launch the kernel directly.
|
