1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
|
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2015 Timesys Corporation
* Copyright 2015 General Electric Company
* Copyright 2012 Freescale Semiconductor, Inc.
*/
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/video.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <miiphy.h>
#include <net.h>
#include <netdev.h>
#include <asm/arch/mxc_hdmi.h>
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
#include <i2c.h>
#include <input.h>
#include <pwm.h>
#include <stdlib.h>
#include "../common/ge_common.h"
#include "../common/vpd_reader.h"
#include "../../../drivers/net/e1000.h"
DECLARE_GLOBAL_DATA_PTR;
struct vpd_cache;
static int confidx = 3; /* Default to b850v3. */
static struct vpd_cache vpd;
#ifndef CONFIG_SYS_I2C_EEPROM_ADDR
# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#endif
#ifndef CONFIG_SYS_I2C_EEPROM_BUS
#define CONFIG_SYS_I2C_EEPROM_BUS 4
#endif
#define NC_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_HYS)
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST)
#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST)
#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
return 0;
}
static iomux_v3_cfg_t const uart3_pads[] = {
MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const uart4_pads[] = {
MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const enet_pads[] = {
MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
/* AR8033 PHY Reset */
MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void setup_iomux_enet(void)
{
imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
/* Reset AR8033 PHY */
gpio_direction_output(IMX_GPIO_NR(1, 28), 0);
mdelay(10);
gpio_set_value(IMX_GPIO_NR(1, 28), 1);
mdelay(1);
}
static iomux_v3_cfg_t const usdhc2_pads[] = {
MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const usdhc3_pads[] = {
MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
static iomux_v3_cfg_t const usdhc4_pads[] = {
MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const ecspi1_pads[] = {
MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static struct i2c_pads_info i2c_pad_info1 = {
.scl = {
.i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
.gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD,
.gp = IMX_GPIO_NR(5, 27)
},
.sda = {
.i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD,
.gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD,
.gp = IMX_GPIO_NR(5, 26)
}
};
static struct i2c_pads_info i2c_pad_info2 = {
.scl = {
.i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
.gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
.gp = IMX_GPIO_NR(4, 12)
},
.sda = {
.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
.gp = IMX_GPIO_NR(4, 13)
}
};
static struct i2c_pads_info i2c_pad_info3 = {
.scl = {
.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD,
.gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD,
.gp = IMX_GPIO_NR(1, 3)
},
.sda = {
.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
.gp = IMX_GPIO_NR(1, 6)
}
};
#ifdef CONFIG_MXC_SPI
int board_spi_cs_gpio(unsigned bus, unsigned cs)
{
return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1;
}
static void setup_spi(void)
{
imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
}
#endif
static iomux_v3_cfg_t const pcie_pads[] = {
MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void setup_pcie(void)
{
imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
}
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
}
#ifdef CONFIG_FSL_ESDHC
struct fsl_esdhc_cfg usdhc_cfg[3] = {
{USDHC2_BASE_ADDR},
{USDHC3_BASE_ADDR},
{USDHC4_BASE_ADDR},
};
#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
#define USDHC4_CD_GPIO IMX_GPIO_NR(6, 11)
int board_mmc_getcd(struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
int ret = 0;
switch (cfg->esdhc_base) {
case USDHC2_BASE_ADDR:
ret = !gpio_get_value(USDHC2_CD_GPIO);
break;
case USDHC3_BASE_ADDR:
ret = 1; /* eMMC is always present */
break;
case USDHC4_BASE_ADDR:
ret = !gpio_get_value(USDHC4_CD_GPIO);
break;
}
return ret;
}
int board_mmc_init(bd_t *bis)
{
int ret;
int i;
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
switch (i) {
case 0:
imx_iomux_v3_setup_multiple_pads(
usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
gpio_direction_input(USDHC2_CD_GPIO);
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
break;
case 1:
imx_iomux_v3_setup_multiple_pads(
usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
break;
case 2:
imx_iomux_v3_setup_multiple_pads(
usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
gpio_direction_input(USDHC4_CD_GPIO);
usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
break;
default:
printf("Warning: you configured more USDHC controllers\n"
"(%d) then supported by the board (%d)\n",
i + 1, CONFIG_SYS_FSL_USDHC_NUM);
return -EINVAL;
}
ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
if (ret)
return ret;
}
return 0;
}
#endif
static int mx6_rgmii_rework(struct phy_device *phydev)
{
/* Configure AR8033 to ouput a 125MHz clk from CLK_25M */
/* set device address 0x7 */
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
/* offset 0x8016: CLK_25M Clock Select */
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
/* enable register write, no post increment, address 0x7 */
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
/* set to 125 MHz from local PLL source */
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18);
/* rgmii tx clock delay enable */
/* set debug port address: SerDes Test and System Mode Control */
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
/* enable rgmii tx clock delay */
/* set the reserved bits to avoid board specific voltage peak issue*/
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3D47);
return 0;
}
int board_phy_config(struct phy_device *phydev)
{
mx6_rgmii_rework(phydev);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
#if defined(CONFIG_VIDEO_IPUV3)
static iomux_v3_cfg_t const backlight_pads[] = {
/* Power for LVDS Display */
MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
#define LVDS_POWER_GP IMX_GPIO_NR(3, 22)
/* Backlight enable for LVDS display */
MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0)
/* backlight PWM brightness control */
MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void do_enable_hdmi(struct display_info_t const *dev)
{
imx_enable_hdmi_phy();
}
int board_cfb_skip(void)
{
gpio_direction_output(LVDS_POWER_GP, 1);
return 0;
}
static int is_b850v3(void)
{
return confidx == 3;
}
static int detect_lcd(struct display_info_t const *dev)
{
return !is_b850v3();
}
struct display_info_t const displays[] = {{
.bus = -1,
.addr = -1,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = detect_lcd,
.enable = NULL,
.mode = {
.name = "G121X1-L03",
.refresh = 60,
.xres = 1024,
.yres = 768,
.pixclock = 15385,
.left_margin = 20,
.right_margin = 300,
.upper_margin = 30,
.lower_margin = 8,
.hsync_len = 1,
.vsync_len = 1,
.sync = FB_SYNC_EXT,
.vmode = FB_VMODE_NONINTERLACED
} }, {
.bus = -1,
.addr = 3,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = detect_hdmi,
.enable = do_enable_hdmi,
.mode = {
.name = "HDMI",
.refresh = 60,
.xres = 1024,
.yres = 768,
.pixclock = 15385,
.left_margin = 220,
.right_margin = 40,
.upper_margin = 21,
.lower_margin = 7,
.hsync_len = 60,
.vsync_len = 10,
.sync = FB_SYNC_EXT,
.vmode = FB_VMODE_NONINTERLACED
} } };
size_t display_count = ARRAY_SIZE(displays);
static void enable_videopll(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
s32 timeout = 100000;
setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
/* PLL_VIDEO 455MHz (24MHz * (37+11/12) / 2)
* |
* PLL5
* |
* CS2CDR[LDB_DI0_CLK_SEL]
* |
* +----> LDB_DI0_SERIAL_CLK_ROOT
* |
* +--> CSCMR2[LDB_DI0_IPU_DIV] --> LDB_DI0_IPU 455 / 7 = 65 MHz
*/
clrsetbits_le32(&ccm->analog_pll_video,
BM_ANADIG_PLL_VIDEO_DIV_SELECT |
BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT,
BF_ANADIG_PLL_VIDEO_DIV_SELECT(37) |
BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1));
writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
clrbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
while (timeout--)
if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
break;
if (timeout < 0)
printf("Warning: video pll lock timeout!\n");
clrsetbits_le32(&ccm->analog_pll_video,
BM_ANADIG_PLL_VIDEO_BYPASS,
BM_ANADIG_PLL_VIDEO_ENABLE);
}
static void setup_display_b850v3(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
enable_videopll();
/* IPU1 DI0 clock is 455MHz / 7 = 65MHz */
setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
imx_setup_hdmi();
/* Set LDB_DI0 as clock source for IPU_DI0 */
clrsetbits_le32(&mxc_ccm->chsccdr,
MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK,
(CHSCCDR_CLK_SEL_LDB_DI0 <<
MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET));
/* Turn on IPU LDB DI0 clocks */
setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
enable_ipu_clock();
writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW |
IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG |
IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT |
IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
IOMUXC_GPR2_SPLIT_MODE_EN_MASK |
IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 |
IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0,
&iomux->gpr[2]);
clrbits_le32(&iomux->gpr[3],
IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
IOMUXC_GPR3_LVDS1_MUX_CTL_MASK |
IOMUXC_GPR3_HDMI_MUX_CTL_MASK);
}
static void setup_display_bx50v3(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
enable_videopll();
/* When a reset/reboot is performed the display power needs to be turned
* off for atleast 500ms. The boot time is ~300ms, we need to wait for
* an additional 200ms here. Unfortunately we use external PMIC for
* doing the reset, so can not differentiate between POR vs soft reset
*/
mdelay(200);
/* IPU1 DI0 clock is 455MHz / 7 = 65MHz */
setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
/* Set LDB_DI0 as clock source for IPU_DI0 */
clrsetbits_le32(&mxc_ccm->chsccdr,
MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK,
(CHSCCDR_CLK_SEL_LDB_DI0 <<
MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET));
/* Turn on IPU LDB DI0 clocks */
setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
enable_ipu_clock();
writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0,
&iomux->gpr[2]);
clrsetbits_le32(&iomux->gpr[3],
IOMUXC_GPR3_LVDS0_MUX_CTL_MASK,
(IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET));
/* backlights off until needed */
imx_iomux_v3_setup_multiple_pads(backlight_pads,
ARRAY_SIZE(backlight_pads));
gpio_direction_input(LVDS_POWER_GP);
gpio_direction_input(LVDS_BACKLIGHT_GP);
}
#endif /* CONFIG_VIDEO_IPUV3 */
/*
* Do not overwrite the console
* Use always serial for U-Boot console
*/
int overwrite_console(void)
{
return 1;
}
#define VPD_TYPE_INVALID 0x00
#define VPD_BLOCK_NETWORK 0x20
#define VPD_BLOCK_HWID 0x44
#define VPD_PRODUCT_B850 1
#define VPD_PRODUCT_B650 2
#define VPD_PRODUCT_B450 3
#define VPD_HAS_MAC1 0x1
#define VPD_HAS_MAC2 0x2
#define VPD_MAC_ADDRESS_LENGTH 6
struct vpd_cache {
u8 product_id;
u8 has;
unsigned char mac1[VPD_MAC_ADDRESS_LENGTH];
unsigned char mac2[VPD_MAC_ADDRESS_LENGTH];
};
/*
* Extracts MAC and product information from the VPD.
*/
static int vpd_callback(void *userdata, u8 id, u8 version, u8 type,
size_t size, u8 const *data)
{
struct vpd_cache *vpd = (struct vpd_cache *)userdata;
if (id == VPD_BLOCK_HWID && version == 1 && type != VPD_TYPE_INVALID &&
size >= 1) {
vpd->product_id = data[0];
} else if (id == VPD_BLOCK_NETWORK && version == 1 &&
type != VPD_TYPE_INVALID) {
if (size >= 6) {
vpd->has |= VPD_HAS_MAC1;
memcpy(vpd->mac1, data, VPD_MAC_ADDRESS_LENGTH);
}
if (size >= 12) {
vpd->has |= VPD_HAS_MAC2;
memcpy(vpd->mac2, data + 6, VPD_MAC_ADDRESS_LENGTH);
}
}
return 0;
}
static void process_vpd(struct vpd_cache *vpd)
{
int fec_index = -1;
int i210_index = -1;
switch (vpd->product_id) {
case VPD_PRODUCT_B450:
env_set("confidx", "1");
i210_index = 0;
fec_index = 1;
break;
case VPD_PRODUCT_B650:
env_set("confidx", "2");
i210_index = 0;
fec_index = 1;
break;
case VPD_PRODUCT_B850:
env_set("confidx", "3");
i210_index = 1;
fec_index = 2;
break;
}
if (fec_index >= 0 && (vpd->has & VPD_HAS_MAC1))
eth_env_set_enetaddr_by_index("eth", fec_index, vpd->mac1);
if (i210_index >= 0 && (vpd->has & VPD_HAS_MAC2))
eth_env_set_enetaddr_by_index("eth", i210_index, vpd->mac2);
}
static int read_vpd(uint eeprom_bus)
{
int res;
int size = 1024;
uint8_t *data;
unsigned int current_i2c_bus = i2c_get_bus_num();
res = i2c_set_bus_num(eeprom_bus);
if (res < 0)
return res;
data = (uint8_t *)malloc(size);
if (!data)
return -ENOMEM;
res = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
CONFIG_SYS_I2C_EEPROM_ADDR_LEN, data, size);
if (res == 0) {
memset(&vpd, 0, sizeof(vpd));
vpd_reader(size, data, &vpd, vpd_callback);
}
free(data);
i2c_set_bus_num(current_i2c_bus);
return res;
}
int board_eth_init(bd_t *bis)
{
setup_iomux_enet();
setup_pcie();
e1000_initialize(bis);
return cpu_eth_init(bis);
}
static iomux_v3_cfg_t const misc_pads[] = {
MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NC_PAD_CTRL),
MX6_PAD_EIM_CS0__GPIO2_IO23 | MUX_PAD_CTRL(NC_PAD_CTRL),
MX6_PAD_EIM_CS1__GPIO2_IO24 | MUX_PAD_CTRL(NC_PAD_CTRL),
MX6_PAD_EIM_OE__GPIO2_IO25 | MUX_PAD_CTRL(NC_PAD_CTRL),
MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NC_PAD_CTRL),
MX6_PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NC_PAD_CTRL),
MX6_PAD_GPIO_9__WDOG1_B | MUX_PAD_CTRL(NC_PAD_CTRL),
};
#define SUS_S3_OUT IMX_GPIO_NR(4, 11)
#define WIFI_EN IMX_GPIO_NR(6, 14)
int board_early_init_f(void)
{
imx_iomux_v3_setup_multiple_pads(misc_pads,
ARRAY_SIZE(misc_pads));
setup_iomux_uart();
#if defined(CONFIG_VIDEO_IPUV3)
/* Set LDB clock to Video PLL */
select_ldb_di_clock_source(MXC_PLL5_CLK);
#endif
return 0;
}
static void set_confidx(const struct vpd_cache* vpd)
{
switch (vpd->product_id) {
case VPD_PRODUCT_B450:
confidx = 1;
break;
case VPD_PRODUCT_B650:
confidx = 2;
break;
case VPD_PRODUCT_B850:
confidx = 3;
break;
}
}
int board_init(void)
{
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
read_vpd(CONFIG_SYS_I2C_EEPROM_BUS);
set_confidx(&vpd);
gpio_direction_output(SUS_S3_OUT, 1);
gpio_direction_output(WIFI_EN, 1);
#if defined(CONFIG_VIDEO_IPUV3)
if (is_b850v3())
setup_display_b850v3();
else
setup_display_bx50v3();
#endif
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_MXC_SPI
setup_spi();
#endif
return 0;
}
#ifdef CONFIG_CMD_BMODE
static const struct boot_mode board_boot_modes[] = {
/* 4 bit bus width */
{"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
{"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
{NULL, 0},
};
#endif
void pmic_init(void)
{
#define I2C_PMIC 0x2
#define DA9063_I2C_ADDR 0x58
#define DA9063_REG_BCORE2_CFG 0x9D
#define DA9063_REG_BCORE1_CFG 0x9E
#define DA9063_REG_BPRO_CFG 0x9F
#define DA9063_REG_BIO_CFG 0xA0
#define DA9063_REG_BMEM_CFG 0xA1
#define DA9063_REG_BPERI_CFG 0xA2
#define DA9063_BUCK_MODE_MASK 0xC0
#define DA9063_BUCK_MODE_MANUAL 0x00
#define DA9063_BUCK_MODE_SLEEP 0x40
#define DA9063_BUCK_MODE_SYNC 0x80
#define DA9063_BUCK_MODE_AUTO 0xC0
uchar val;
i2c_set_bus_num(I2C_PMIC);
i2c_read(DA9063_I2C_ADDR, DA9063_REG_BCORE2_CFG, 1, &val, 1);
val &= ~DA9063_BUCK_MODE_MASK;
val |= DA9063_BUCK_MODE_SYNC;
i2c_write(DA9063_I2C_ADDR, DA9063_REG_BCORE2_CFG, 1, &val, 1);
i2c_read(DA9063_I2C_ADDR, DA9063_REG_BCORE1_CFG, 1, &val, 1);
val &= ~DA9063_BUCK_MODE_MASK;
val |= DA9063_BUCK_MODE_SYNC;
i2c_write(DA9063_I2C_ADDR, DA9063_REG_BCORE1_CFG, 1, &val, 1);
i2c_read(DA9063_I2C_ADDR, DA9063_REG_BPRO_CFG, 1, &val, 1);
val &= ~DA9063_BUCK_MODE_MASK;
val |= DA9063_BUCK_MODE_SYNC;
i2c_write(DA9063_I2C_ADDR, DA9063_REG_BPRO_CFG, 1, &val, 1);
i2c_read(DA9063_I2C_ADDR, DA9063_REG_BIO_CFG, 1, &val, 1);
val &= ~DA9063_BUCK_MODE_MASK;
val |= DA9063_BUCK_MODE_SYNC;
i2c_write(DA9063_I2C_ADDR, DA9063_REG_BIO_CFG, 1, &val, 1);
i2c_read(DA9063_I2C_ADDR, DA9063_REG_BMEM_CFG, 1, &val, 1);
val &= ~DA9063_BUCK_MODE_MASK;
val |= DA9063_BUCK_MODE_SYNC;
i2c_write(DA9063_I2C_ADDR, DA9063_REG_BMEM_CFG, 1, &val, 1);
i2c_read(DA9063_I2C_ADDR, DA9063_REG_BPERI_CFG, 1, &val, 1);
val &= ~DA9063_BUCK_MODE_MASK;
val |= DA9063_BUCK_MODE_SYNC;
i2c_write(DA9063_I2C_ADDR, DA9063_REG_BPERI_CFG, 1, &val, 1);
}
int board_late_init(void)
{
process_vpd(&vpd);
#ifdef CONFIG_CMD_BMODE
add_board_boot_modes(board_boot_modes);
#endif
if (is_b850v3())
env_set("videoargs", "video=DP-1:1024x768@60 video=HDMI-A-1:1024x768@60");
else
env_set("videoargs", "video=LVDS-1:1024x768@65");
/* board specific pmic init */
pmic_init();
check_time();
return 0;
}
/*
* Removes the 'eth[0-9]*addr' environment variable with the given index
*
* @param index [in] the index of the eth_device whose variable is to be removed
*/
static void remove_ethaddr_env_var(int index)
{
char env_var_name[9];
sprintf(env_var_name, index == 0 ? "ethaddr" : "eth%daddr", index);
env_set(env_var_name, NULL);
}
int last_stage_init(void)
{
int i;
/*
* Remove first three ethaddr which may have been created by
* function process_vpd().
*/
for (i = 0; i < 3; ++i)
remove_ethaddr_env_var(i);
return 0;
}
int checkboard(void)
{
printf("BOARD: %s\n", CONFIG_BOARD_NAME);
return 0;
}
static int do_backlight_enable(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
#ifdef CONFIG_VIDEO_IPUV3
/* We need at least 200ms between power on and backlight on
* as per specifications from CHI MEI */
mdelay(250);
/* enable backlight PWM 1 */
pwm_init(0, 0, 0);
/* duty cycle 5000000ns, period: 5000000ns */
pwm_config(0, 5000000, 5000000);
/* Backlight Power */
gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
pwm_enable(0);
#endif
return 0;
}
U_BOOT_CMD(
bx50_backlight_enable, 1, 1, do_backlight_enable,
"enable Bx50 backlight",
""
);
|