aboutsummaryrefslogtreecommitdiff
path: root/board/kobol/helios4/helios4.c
blob: 341678319a461199d81c0d793a3008145dd77dd8 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
// SPDX-License-Identifier: GPL-2.0+
/*
 * Copyright (C) 2018 Dennis Gilmore <dgilmore@redhat.com>
 *  based on board/solidrun/clearfog/clearfog.c
 */

#include <common.h>
#include <i2c.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>

#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
#include <../serdes/a38x/high_speed_env_spec.h>

DECLARE_GLOBAL_DATA_PTR;

#define ETH_PHY_CTRL_REG		0
#define ETH_PHY_CTRL_POWER_DOWN_BIT	11
#define ETH_PHY_CTRL_POWER_DOWN_MASK	BIT(ETH_PHY_CTRL_POWER_DOWN_BIT)

/*
 * Those values and defines are taken from the Marvell U-Boot version
 * "u-boot-2013.01-15t1-helios4" as well as the upstream config for clearfog
 */
#define BOARD_GPP_OUT_ENA_LOW	0xffffffff
#define BOARD_GPP_OUT_ENA_MID	0xffffffff

#define BOARD_GPP_OUT_VAL_LOW	0x0
#define BOARD_GPP_OUT_VAL_MID	0x0
#define BOARD_GPP_POL_LOW	0x0
#define BOARD_GPP_POL_MID	0x0

/* IO expander on Marvell GP board includes e.g. fan enabling */
struct marvell_io_exp {
	u8 addr;
	u8 val;
};

static struct marvell_io_exp io_exp[] = {
	{6, 0xf9},
	{2, 0x46}, /* Assert reset signals and enable USB3 current limiter */
	{6, 0xb9}
};

static struct serdes_map board_serdes_map[] = {
	{SATA0, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
	{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
	{SATA1, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
	{SATA3, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
	{SATA2, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
	{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
};

int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
{
	*serdes_map_array = board_serdes_map;
	*count = ARRAY_SIZE(board_serdes_map);
	return 0;
}

/*
 * Define the DDR layout / topology here in the board file. This will
 * be used by the DDR3 init code in the SPL U-Boot version to configure
 * the DDR3 controller.
 */
static struct mv_ddr_topology_map board_topology_map = {
	DEBUG_LEVEL_ERROR,
	0x1, /* active interfaces */
	/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
	{ { { {0x1, 0, 0, 0},
	      {0x1, 0, 0, 0},
	      {0x1, 0, 0, 0},
	      {0x1, 0, 0, 0},
	      {0x1, 0, 0, 0} },
	    SPEED_BIN_DDR_1600K,	/* speed_bin */
	    MV_DDR_DEV_WIDTH_16BIT,	/* memory_width */
	    MV_DDR_DIE_CAP_8GBIT,	/* mem_size */
	    DDR_FREQ_800,		/* frequency */
	    0, 0,			/* cas_wl cas_l */
	    MV_DDR_TEMP_LOW,		/* temperature */
	    MV_DDR_TIM_DEFAULT} },	/* timing */
	BUS_MASK_32BIT_ECC,		/* Busses mask */
	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
	{ {0} },			/* raw spd data */
	{0}				/* timing parameters */
};

struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
{
	/* Return the board topology as defined in the board code */
	return &board_topology_map;
}

int board_early_init_f(void)
{
	/* Configure MPP */
	writel(0x11111111, MVEBU_MPP_BASE + 0x00);
	writel(0x11111111, MVEBU_MPP_BASE + 0x04);
	writel(0x10400011, MVEBU_MPP_BASE + 0x08);
	writel(0x22043333, MVEBU_MPP_BASE + 0x0c);
	writel(0x44400002, MVEBU_MPP_BASE + 0x10);
	writel(0x41144004, MVEBU_MPP_BASE + 0x14);
	writel(0x40333333, MVEBU_MPP_BASE + 0x18);
	writel(0x00004444, MVEBU_MPP_BASE + 0x1c);

	/* Set GPP Out value */
	writel(BOARD_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
	writel(BOARD_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);

	/* Set GPP Polarity */
	writel(BOARD_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
	writel(BOARD_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);

	/* Set GPP Out Enable */
	writel(BOARD_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
	writel(BOARD_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);

	return 0;
}

int board_init(void)
{
	int i;

	/* Address of boot parameters */
	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;

	/* Init I2C IO expanders */
	for (i = 0; i < ARRAY_SIZE(io_exp); i++) {
		struct udevice *dev;
		int ret;

		ret = i2c_get_chip_for_busnum(0, io_exp[i].addr, 1, &dev);
		if (ret) {
			printf("Cannot find I2C: %d\n", ret);
			return 0;
		}

		ret = dm_i2c_write(dev, io_exp[i].val, &io_exp[i].val, 1);
		if (ret) {
			printf("Failed to set IO expander via I2C\n");
			return -EIO;
		}
	}

	return 0;
}

int checkboard(void)
{
	puts("Board: Helios4\n");

	return 0;
}

int board_eth_init(bd_t *bis)
{
	cpu_eth_init(bis); /* Built in controller(s) come first */
	return pci_eth_init(bis);
}