1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
|
// SPDX-License-Identifier: GPL-2.0
/*
* board/renesas/stout/stout.c
* This file is Stout board support.
*
* Copyright (C) 2015 Renesas Electronics Europe GmbH
* Copyright (C) 2015 Renesas Electronics Corporation
* Copyright (C) 2015 Cogent Embedded, Inc.
*/
#include <common.h>
#include <malloc.h>
#include <netdev.h>
#include <dm.h>
#include <dm/platform_data/serial_sh.h>
#include <environment.h>
#include <asm/processor.h>
#include <asm/mach-types.h>
#include <asm/io.h>
#include <linux/errno.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/arch/rmobile.h>
#include <asm/arch/rcar-mstp.h>
#include <asm/arch/mmc.h>
#include <asm/arch/sh_sdhi.h>
#include <miiphy.h>
#include <i2c.h>
#include <mmc.h>
#include "qos.h"
#include "cpld.h"
DECLARE_GLOBAL_DATA_PTR;
#define CLK2MHZ(clk) (clk / 1000 / 1000)
void s_init(void)
{
struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE;
struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE;
/* Watchdog init */
writel(0xA5A5A500, &rwdt->rwtcsra);
writel(0xA5A5A500, &swdt->swtcsra);
/* CPU frequency setting. Set to 1.4GHz */
if (rmobile_get_cpu_rev_integer() >= R8A7790_CUT_ES2X) {
u32 stat = 0;
u32 stc = ((1400 / CLK2MHZ(CONFIG_SYS_CLK_FREQ)) - 1)
<< PLL0_STC_BIT;
clrsetbits_le32(PLL0CR, PLL0_STC_MASK, stc);
do {
stat = readl(PLLECR) & PLL0ST;
} while (stat == 0x0);
}
/* QoS(Quality-of-Service) Init */
qos_init();
}
#define TMU0_MSTP125 BIT(25)
#define SD2CKCR 0xE6150078
#define SD2_97500KHZ 0x7
int board_early_init_f(void)
{
/* TMU0 */
mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);
/*
* SD0 clock is set to 97.5MHz by default.
* Set SD2 to the 97.5MHz as well.
*/
writel(SD2_97500KHZ, SD2CKCR);
return 0;
}
#define ETHERNET_PHY_RESET 123 /* GPIO 3 31 */
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
cpld_init();
/* Force ethernet PHY out of reset */
gpio_request(ETHERNET_PHY_RESET, "phy_reset");
gpio_direction_output(ETHERNET_PHY_RESET, 0);
mdelay(20);
gpio_direction_output(ETHERNET_PHY_RESET, 1);
return 0;
}
int dram_init(void)
{
if (fdtdec_setup_memory_size() != 0)
return -EINVAL;
return 0;
}
int dram_init_banksize(void)
{
fdtdec_setup_memory_banksize();
return 0;
}
/* Stout has KSZ8041NL/RNL */
#define PHY_CONTROL1 0x1E
#define PHY_LED_MODE 0xC0000
#define PHY_LED_MODE_ACK 0x4000
int board_phy_config(struct phy_device *phydev)
{
int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1);
ret &= ~PHY_LED_MODE;
ret |= PHY_LED_MODE_ACK;
ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret);
return 0;
}
enum env_location env_get_location(enum env_operation op, int prio)
{
const u32 load_magic = 0xb33fc0de;
/* Block environment access if loaded using JTAG */
if ((readl(CONFIG_SPL_TEXT_BASE + 0x24) == load_magic) &&
(op != ENVOP_INIT))
return ENVL_UNKNOWN;
if (prio)
return ENVL_UNKNOWN;
return ENVL_SPI_FLASH;
}
|
