1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
|
/*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <config.h>
#include <common.h>
#include <mpc8xx.h>
#include "pld.h"
#include "hpi.h"
#define _NOT_USED_ 0xFFFFFFFF
static long int dram_size (long int, long int *, long int);
const uint sdram_table[] = {
/*
* Single Read. (Offset 0 in UPMB RAM)
*/
0x1F07FC04, 0xEEAEFC04, 0x11ADFC04, 0xEFBBBC00,
0x1FF77C47, /* last */
/*
* SDRAM Initialization (offset 5 in UPMB RAM)
*
* This is no UPM entry point. The following definition uses
* the remaining space to establish an initialization
* sequence, which is executed by a RUN command.
*
*/
0x1FF77C34, 0xEFEABC34, 0x1FB57C35, /* last */
/*
* Burst Read. (Offset 8 in UPMB RAM)
*/
0x1F07FC04, 0xEEAEFC04, 0x10ADFC04, 0xF0AFFC00,
0xF0AFFC00, 0xF1AFFC00, 0xEFBBBC00, 0x1FF77C47, /* last */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Single Write. (Offset 18 in UPMB RAM)
*/
0x1F07FC04, 0xEEAEBC00, 0x01B93C04, 0x1FF77C47, /* last */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Burst Write. (Offset 20 in UPMB RAM)
*/
0x1F07FC04, 0xEEAEBC00, 0x10AD7C00, 0xF0AFFC00,
0xF0AFFC00, 0xE1BBBC04, 0x1FF77C47, /* last */
_NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Refresh (Offset 30 in UPMB RAM)
*/
0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
0xFFFFFC84, 0xFFFFFC07, /* last */
_NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Exception. (Offset 3c in UPMB RAM)
*/
0x7FFFFC07, /* last */
_NOT_USED_, _NOT_USED_, _NOT_USED_,
};
phys_size_t initdram (int board_type)
{
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immr->im_memctl;
/* volatile spc1920_pld_t *pld = (spc1920_pld_t *) CONFIG_SYS_SPC1920_PLD_BASE; */
long int size_b0;
long int size8, size9;
int i;
/*
* Configure UPMB for SDRAM
*/
upmconfig (UPMB, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
udelay(100);
memctl->memc_mptpr = CONFIG_SYS_MPTPR;
/* burst length=4, burst type=sequential, CAS latency=2 */
memctl->memc_mar = CONFIG_SYS_MAR;
/*
* Map controller bank 1 to the SDRAM bank at preliminary address.
*/
memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
/* initialize memory address register */
memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL; /* refresh not enabled yet */
/* mode initialization (offset 5) */
udelay (200); /* 0x80006105 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x05);
/* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */
udelay (1); /* 0x80006130 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
udelay (1); /* 0x80006130 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
udelay (1); /* 0x80006106 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x06);
memctl->memc_mbmr |= MBMR_PTBE; /* refresh enabled */
udelay (200);
/* Need at least 10 DRAM accesses to stabilize */
for (i = 0; i < 10; ++i) {
volatile unsigned long *addr =
(volatile unsigned long *) CONFIG_SYS_SDRAM_BASE;
unsigned long val;
val = *(addr + i);
*(addr + i) = val;
}
/*
* Check Bank 0 Memory Size for re-configuration
*
* try 8 column mode
*/
size8 = dram_size (CONFIG_SYS_MBMR_8COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
udelay (1000);
/*
* try 9 column mode
*/
size9 = dram_size (CONFIG_SYS_MBMR_9COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
if (size8 < size9) { /* leave configuration at 9 columns */
size_b0 = size9;
memctl->memc_mbmr = CONFIG_SYS_MBMR_9COL | MBMR_PTBE;
udelay (500);
} else { /* back to 8 columns */
size_b0 = size8;
memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL | MBMR_PTBE;
udelay (500);
}
/*
* Final mapping:
*/
memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) |
OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING;
memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V;
udelay (1000);
/* initalize the DSP Host Port Interface */
hpi_init();
/* FRAM Setup */
memctl->memc_or4 = CONFIG_SYS_OR4;
memctl->memc_br4 = CONFIG_SYS_BR4;
udelay(1000);
return (size_b0);
}
/*
* Check memory range for valid RAM. A simple memory test determines
* the actually available RAM size between addresses `base' and
* `base + maxsize'. Some (not all) hardware errors are detected:
* - short between address lines
* - short between data lines
*/
static long int dram_size (long int mbmr_value, long int *base,
long int maxsize)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
memctl->memc_mbmr = mbmr_value;
return (get_ram_size (base, maxsize));
}
/************* other stuff ******************/
int board_early_init_f(void)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
/* Set Go/NoGo led (PA15) to color red */
immap->im_ioport.iop_papar &= ~0x1;
immap->im_ioport.iop_paodr &= ~0x1;
immap->im_ioport.iop_padir |= 0x1;
immap->im_ioport.iop_padat |= 0x1;
#if 0
/* Turn on LED PD9 */
immap->im_ioport.iop_pdpar &= ~(0x0040);
immap->im_ioport.iop_pddir |= 0x0040;
immap->im_ioport.iop_pddat |= 0x0040;
#endif
/*
* Enable console on SMC1. This requires turning on
* the com2_en signal and SMC1_DISABLE
*/
/* SMC1_DISABLE: PB17 */
immap->im_cpm.cp_pbodr &= ~0x4000;
immap->im_cpm.cp_pbpar &= ~0x4000;
immap->im_cpm.cp_pbdir |= 0x4000;
immap->im_cpm.cp_pbdat &= ~0x4000;
/* COM2_EN: PD10 */
immap->im_ioport.iop_pdpar &= ~0x0020;
immap->im_ioport.iop_pddir &= ~0x4000;
immap->im_ioport.iop_pddir |= 0x0020;
immap->im_ioport.iop_pddat |= 0x0020;
#ifdef CONFIG_SYS_SMC1_PLD_CLK4 /* SMC1 uses CLK4 from PLD */
immap->im_cpm.cp_simode |= 0x7000;
immap->im_cpm.cp_simode &= ~(0x8000);
#endif
return 0;
}
int last_stage_init(void)
{
#ifdef CONFIG_SPC1920_HPI_TEST
printf("CMB1920 Host Port Interface Test: %s\n",
hpi_test() ? "Failed!" : "OK");
#endif
return 0;
}
int checkboard (void)
{
puts("Board: SPC1920\n");
return 0;
}
|
