blob: 622bef537488f9da204e13f008eadf0ff1796fe5 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
|
Nios Development Kit
Startix Editions
Last Update: January 28, 2004
====================================================================
This file contains information regarding U-Boot and the Altera
Nios Development Kit, Startix Edition (DK-1S10). For general Nios
information see doc/README.nios.
Most stuff of this file was borrowed and based on README.dk1c20,
the DK-1C20 related information file.
For those interested in contributing ... see HELP WANTED section
in doc/README.nios.
Contents:
1. Files
2. Memory Organization
3. CPU Variations
4. Examples
5. Programming U-Boot into FLASH with GERMS
====================================================================
1. Files
=========
board/altera/dk1s10/*
include/configs/DK1S10.h
2. Memory Organization
=======================
-The heap is placed below the monitor (U-Boot code).
-Global data is placed below the heap.
-The stack is placed below global data (&grows down).
3. CPU Variations
=================
There are more than one NIOS CPU variation for the DK-1S10. U-Boot
supports the following CPU configurations:
- Altera Standard 32 (make DK1S10_standard_32_config)
- Microtronix LDK 2.0 (make DK1S10_mtx_ldk_20_config)
4. Examples
============
The hello_world example was never tested on DK-1S10. Neverthelse
it should work as far as possible, because the DK-1S10 port is
more than ninetieth percents equal to the DK-1C20 port and at
this platform the hello_world example was already tested
successfully (see README.dk1c20).
5. Programming U-Boot into FLASH with GERMS
============================================
The current version of the DK-1S10 port with the default
configuration settings occupies about 78 KBytes of flash.
A minimal configuration occupies less than 60 KByte
(network support disabled).
To program U-Boot into the DK-1S10 flash using GERMS do the
following:
1. From the command line, download U-Boot using the nios-run:
$ nios-run -r u-boot.srec
This takes about 45 seconds (GERMS is not very speedy here).
After u-boot is downloaded it will be executed. You should
see the following:
U-Boot 1.0.2 (Jan 28 2004 - 19:02:30)
CPU: Nios-32 Rev. 3.3 (0x3038)
Reg file size: 256 LO_LIMIT/HI_LIMIT: 2/14
Board: Altera Nios 1S10 Development Kit
In: serial
Out: serial
Err: serial
DK1S10 >
2. Quit nios-run and start your terminal application (e.g. start
Hyperterminal or minicom).
3. Download the u-boot code to RAM. When using Hyperterminal, do the
following:
a. From the u-boot command prompt start a binary download to
SRAM / SDRAM:
at the Altera Standard 32 to SRAM:
==> loadb 800000
at the Microtronix LDK 2.0 to SDRAM:
==> loadb 1010000
b. Download u-boot.bin using kermit.
4. From the U-Boot command prompt, erase flash:
at the Altera Standard 32 from 0x40000 to 0x5ffff:
==> erase 1:4-5
at the Microtronix LDK 2.0 from 0x8000000 to 0x81ffff:
==> erase 1:0-1
5. Copy the binary image from SRAM / SDRAM to flash:
at the Altera Standard 32 to SRAM:
==> cp.b 800000 40000 ${filesize}
at the Microtronix LDK 2.0 to SDRAM:
==> cp.b 1010000 8000000 ${filesize}
U-Boot will now automatically start when the board is powered on or
reset using the Standard-32 configuration. To start U-Boot with the
Safe-32 configuration, enter the following GERMS command:
+ g 40000
|
