blob: 4959590b8b37720c9be0ae29d25bf5fda0104115 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
.. SPDX-License-Identifier: GPL-2.0+
U-Boot for Khadas VIM3 (A311D)
==============================
Khadas VIM3 is a Single Board Computer manufactured by Shenzhen Wesion Technology Co. Ltd
with the following specifications:
- Amlogic A311D Arm Cortex-A53 dual-core + Cortex-A73 quad-core SoC
- 4GB LPDDR4 SDRAM
- Gigabit Ethernet
- HDMI 2.1 display
- 40-pin GPIO header
- 1 x USB 3.0 Host, 1 x USB 2.0 Host
- eMMC, microSD
- M.2
- Infrared receiver
Schematics are available on the manufacturer website.
PCIe Setup
----------
The on-board MCU can mux the PCIe/USB3.0 shared differential lines using a FUSB340TMX USB
3.1 SuperSpeed Data Switch between a USB3.0 Type-A connector and an M.2 Key M slot. The
PHY driving these differential lines is shared between the USB3.0 controller and the PCIe
Controller, thus only a single controller can use it.
To setup for PCIe run the following commands from U-Boot then power-cycle the board:
.. code-block:: none
i2c dev i2c@5000
i2c mw 0x18 0x33 1
To revert to USB3.0 run the following commands from U-Boot then power-cycle the board:
.. code-block:: none
i2c dev i2c@5000
i2c mw 0x18 0x33 0
U-Boot Compilation
------------------
.. code-block:: bash
$ export CROSS_COMPILE=aarch64-none-elf-
$ make khadas-vim3_defconfig
$ make
U-Boot Signing with Pre-Built FIP repo
--------------------------------------
.. code-block:: bash
$ git clone https://github.com/LibreELEC/amlogic-boot-fip --depth=1
$ cd amlogic-boot-fip
$ mkdir my-output-dir
$ ./build-fip.sh khadas-vim3 /path/to/u-boot/u-boot.bin my-output-dir
U-Boot Manual Signing
---------------------
Amlogic does not provide sources for the firmware and tools needed to create a bootloader
image so it is necessary to obtain binaries from sources published by the board vendor:
.. code-block:: bash
$ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
$ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
$ tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
$ tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
$ export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
$ DIR=vim3-u-boot
$ git clone --depth 1 https://github.com/khadas/u-boot.git -b khadas-vims-v2015.01 $DIR
$ cd vim3-u-boot
$ make kvim3_defconfig
$ make CROSS_COMPILE=aarch64-none-elf-
$ export UBOOTDIR=$PWD
Go back to the mainline U-Boot source tree then:
.. code-block:: bash
$ mkdir fip
$ wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
$ cp $UBOOTDIR/build/scp_task/bl301.bin fip/
$ cp $UBOOTDIR/build/board/khadas/kvim3/firmware/acs.bin fip/
$ cp $UBOOTDIR/fip/g12b/bl2.bin fip/
$ cp $UBOOTDIR/fip/g12b/bl30.bin fip/
$ cp $UBOOTDIR/fip/g12b/bl31.img fip/
$ cp $UBOOTDIR/fip/g12b/ddr3_1d.fw fip/
$ cp $UBOOTDIR/fip/g12b/ddr4_1d.fw fip/
$ cp $UBOOTDIR/fip/g12b/ddr4_2d.fw fip/
$ cp $UBOOTDIR/fip/g12b/diag_lpddr4.fw fip/
$ cp $UBOOTDIR/fip/g12b/lpddr3_1d.fw fip/
$ cp $UBOOTDIR/fip/g12b/lpddr4_1d.fw fip/
$ cp $UBOOTDIR/fip/g12b/lpddr4_2d.fw fip/
$ cp $UBOOTDIR/fip/g12b/piei.fw fip/
$ cp $UBOOTDIR/fip/g12b/aml_ddr.fw fip/
$ cp u-boot.bin fip/bl33.bin
$ bash fip/blx_fix.sh \
fip/bl30.bin \
fip/zero_tmp \
fip/bl30_zero.bin \
fip/bl301.bin \
fip/bl301_zero.bin \
fip/bl30_new.bin \
bl30
$ bash fip/blx_fix.sh \
fip/bl2.bin \
fip/zero_tmp \
fip/bl2_zero.bin \
fip/acs.bin \
fip/bl21_zero.bin \
fip/bl2_new.bin \
bl2
$ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl30sig --input fip/bl30_new.bin \
--output fip/bl30_new.bin.g12a.enc \
--level v3
$ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl30_new.bin.g12a.enc \
--output fip/bl30_new.bin.enc \
--level v3 --type bl30
$ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl31.img \
--output fip/bl31.img.enc \
--level v3 --type bl31
$ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl33.bin --compress lz4 \
--output fip/bl33.bin.enc \
--level v3 --type bl33 --compress lz4
$ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl2sig --input fip/bl2_new.bin \
--output fip/bl2.n.bin.sig
$ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bootmk \
--output fip/u-boot.bin \
--bl2 fip/bl2.n.bin.sig \
--bl30 fip/bl30_new.bin.enc \
--bl31 fip/bl31.img.enc \
--bl33 fip/bl33.bin.enc \
--ddrfw1 fip/ddr4_1d.fw \
--ddrfw2 fip/ddr4_2d.fw \
--ddrfw3 fip/ddr3_1d.fw \
--ddrfw4 fip/piei.fw \
--ddrfw5 fip/lpddr4_1d.fw \
--ddrfw6 fip/lpddr4_2d.fw \
--ddrfw7 fip/diag_lpddr4.fw \
--ddrfw8 fip/aml_ddr.fw \
--ddrfw9 fip/lpddr3_1d.fw \
--level v3
Then write U-Boot to SD or eMMC with:
.. code-block:: bash
$ DEV=/dev/boot_device
$ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
$ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=440
|
