1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
|
.. SPDX-License-Identifier: GPL-2.0+
Kontron SMARC-sAL28
===================
The Kontron SMARC-sAL28 board is a TSN-enabled dual-core ARM A72
processor module with an on-chip 6-port TSN switch and a 3D GPU.
Quickstart
----------
Compile U-Boot
^^^^^^^^^^^^^^
Configure and compile the binary::
$ make kontron_sl28_defconfig
$ CROSS_COMPILE=aarch64-linux-gnu make
Copy u-boot.rom to a TFTP server.
Install the bootloader on the board
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
To install the bootloader binary use the following command::
> tftp path/to/u-boot.rom
> sf probe 0
> sf update $fileaddr 0x210000 $filesize
The board is fully failsafe, you can't break anything. If builtin watchdog
is enabled, you'll automatically end up in the failsafe bootloader if
something goes wrong. If the watchdog is disabled, you have to manually
enter failsafe mode by asserting the ``FORCE_RECOV#`` line during board
reset.
Update image
------------
After the build finished, there will be an update image called
u-boot-update.bin. This can either be used in the DFU mode (which isn't
supported yet) or encapsulated in an EFI UpdateCapsule.
To build the capsule use the following command
$ tools/mkeficapsule -f u-boot-update.bin -i 1 UpdateUboot
Afterward you can copy this file to your ESP into the /EFI/UpdateCapsule/
folder. On the next EFI boot this will automatically update your
bootloader.
Builtin watchdog
----------------
The builtin watchdog will supervise the bootloader startup. If anything
goes wrong it will reset the board and boot into the failsafe bootloader.
Once the bootloader is started successfully, it will disable the watchdog
timer.
wdt command flags
^^^^^^^^^^^^^^^^^
The `wdt start` as well as the `wdt expire` command take a flags argument.
The supported bitmask is as follows.
| Bit | Description |
| --- | ----------------------------- |
| 0 | Enable failsafe mode |
| 1 | Lock the control register |
| 2 | Disable board reset |
| 3 | Enable WDT_TIME_OUT# line |
For example, you can use `wdt expire 1` to issue a reset and boot into the
failsafe bootloader.
Disable the builtin watchdog
^^^^^^^^^^^^^^^^^^^^^^^^^^^^
If for some reason, this isn't a desired behavior, the watchdog can also
be configured to not be enabled on board reset. It's configuration is saved
in the non-volatile board configuration bits. To change these you can use
the `sl28 nvm` command.
For more information on the non-volatile board configuration bits, see the
following section.
Non-volatile Board Configuration Bits
-------------------------------------
The board has 16 configuration bits which are stored in the CPLD and are
non-volatile. These can be changed by the `sl28 nvm` command.
=== ===============================================================
Bit Description
=== ===============================================================
0 Power-on inhibit
1 Enable eMMC boot
2 Enable watchdog by default
3 Disable failsafe watchdog by default
4 Clock generator selection bit 0
5 Clock generator selection bit 1
6 Disable CPU SerDes clock #2 and PCIe-A clock output
7 Disable PCIe-B and PCIe-C clock output
8 Keep onboard PHYs in reset
9 Keep USB hub in reset
10 Keep eDP-to-LVDS converter in reset
11 Enable I2C stuck recovery on I2C PM and I2C GP busses
12 Enable automatic onboard PHY H/W reset
13 reserved
14 Used by the RCW to determine boot source
15 Used by the RCW to determine boot source
=== ===============================================================
Please note, that if the board is in failsafe mode, the bits will have the
factory defaults, ie. all bits are off.
Power-On Inhibit
^^^^^^^^^^^^^^^^
If this is set, the board doesn't automatically turn on when power is
applied. Instead, the user has to either toggle the ``PWR_BTN#`` line or
use any other wake-up source such as RTC alarm or Wake-on-LAN.
eMMC Boot
^^^^^^^^^
If this is set, the RCW will be fetched from the on-board eMMC at offset
1MiB. For further details, have a look at the `Reset Configuration Word
Documentation`_.
Watchdog
^^^^^^^^
By default, the CPLD watchdog is enabled in failsafe mode. Using bits 2 and
3, the user can change its mode or disable it altogether.
===== ===== ===============================
Bit 2 Bit 3 Description
===== ===== ===============================
0 0 Watchdog enabled, failsafe mode
0 1 Watchdog disabled
1 0 Watchdog enabled, failsafe mode
1 1 Watchdog enabled, normal mode
===== ===== ===============================
Clock Generator Select
^^^^^^^^^^^^^^^^^^^^^^
The board is prepared to supply different SerDes clock speeds. But for now,
only setting 0 is supported, otherwise the CPU will hang because the PLL
will not lock.
Clock Output Disable And Keep Devices In Reset
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
To safe power, the user might disable different devices and clock output of
the board. It is not supported to disable the "CPU SerDes clock #2" for
now, otherwise the CPU will hang because the PLL will not lock.
Automatic reset of the onboard PHYs
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
By default, there is no hardware reset of the onboard PHY. This is because
for Wake-on-LAN, some registers have to retain their values. If you don't
use the WOL feature and a soft reset of the PHY is not enough you can
enable the hardware reset. The onboard PHY hardware reset follows the
power-on reset.
Further documentation
---------------------
- `Vendor Documentation`_
- `Reset Configuration Word Documentation`_
.. _Reset Configuration Word Documentation: https://raw.githubusercontent.com/kontron/rcw-smarc-sal28/master/README.md
.. _Vendor Documentation: https://raw.githubusercontent.com/kontron/u-boot-smarc-sal28/master/board/kontron/sl28/README.md
|
