1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
|
/* U-boot for BlackVME. (C) Wojtek Skulski 2010.
* The board includes ADSP-BF561 rev. 0.5,
* 32-bit SDRAM (2 * MT48LC16M16A2TG or MT48LC32M16A2TG),
* Gigabit Ether AX88180 (ASIX) + 88E1111 rev. B2 (Marvell),
* SPI boot flash on PF2 (M25P64 8MB, or M25P128 16 MB),
* FPGA boot flash on PF3 (M25P64 8MB, or M25P128 16 MB),
* Spartan6-LX150 (memory-mapped; both PPIs also connected).
* See http://www.skutek.com
*/
#ifndef __CONFIG_BLACKVME_H__
#define __CONFIG_BLACKVME_H__
#include <asm/config-pre.h>
/* Debugging: Set these options if you're having problems
* #define CONFIG_DEBUG_EARLY_SERIAL
* #define DEBUG
* #define CONFIG_DEBUG_DUMP
* #define CONFIG_DEBUG_DUMP_SYMS
* CONFIG_PANIC_HANG means that the board will not auto-reboot
*/
#define CONFIG_PANIC_HANG 0
/* CPU Options */
#define CONFIG_BFIN_CPU bf561-0.5
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER
/*
* CLOCK SETTINGS CAVEAT
* You CANNOT just change the clock settings, esp. the SCLK.
* The SDRAM timing, SPI baud, and the serial UART baud
* use SCLK frequency to set their own frequencies. Therefore,
* if you change the SCLK_DIV, you may also have to adjust
* SDRAM refresh and other timings.
* --------------------------------------------------------------
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* 25 * 8 / 1 = 200 MHz
* 25 * 16 / 1 = 400 MHz
* 25 * 24 / 1 = 600 MHz
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
* 25 * 8 / 2 = 100 MHz
* 25 * 24 / 6 = 100 MHz
* 25 * 24 / 5 = 120 MHz
* 25 * 16 / 3 = 133 MHz
* 25 MHz because the oscillator also feeds the ether chip.
* CONFIG_CLKIN_HZ is 25 MHz written in Hz
* CLKIN_HALF controls the DF bit in PLL_CTL
* 0 = CLKIN 1 = CLKIN / 2
* PLL_BYPASS controls the BYPASS bit in PLL_CTL
* 0 = do not bypass 1 = bypass PLL
* VCO_MULT = MSEL (multiplier) in PLL_CTL
* Values can range from 0-63 (where 0 means 64)
* CCLK_DIV = core clock divider (1, 2, 4, or 8 ONLY)
* SCLK_DIV = system clock divider, 1 to 15
*/
#define CONFIG_CLKIN_HZ 25000000
#define CONFIG_CLKIN_HALF 0
#define CONFIG_PLL_BYPASS 0
#define CONFIG_VCO_MULT 8
#define CONFIG_CCLK_DIV 1
#define CONFIG_SCLK_DIV 2
/*
* Ether chip in async memory space AMS3, same as BF561-EZ-KIT.
* Used in 32-bit mode. 16-bit mode not supported.
* http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:ax88180
*/
/*
* Network settings using a dedicated 2nd ether card in PC
* Windows will automatically acquire IP of that card
* Then use the dedicated card IP + 1 for the board
* http://docs.blackfin.uclinux.org/doku.php?id=setting_up_the_network
*/
#define CONFIG_DRIVER_AX88180 1
#define AX88180_BASE 0x2c000000
#define CONFIG_CMD_MII /* enable probing PHY */
#define CONFIG_HOSTNAME blackvme /* Bfin board */
#define CONFIG_IPADDR 169.254.144.145 /* Bfin board */
#define CONFIG_GATEWAYIP 169.254.144.144 /* dedic card */
#define CONFIG_SERVERIP 169.254.144.144 /* tftp server */
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_ROOTPATH "/export/uClinux-dist/romfs" /*NFS*/
#define CFG_AUTOLOAD "no"
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
#define CONFIG_ENV_OVERWRITE 1 /* enable changing MAC at runtime */
/* Comment out hardcoded MAC to enable MAC storage in EEPROM */
/* # define CONFIG_ETHADDR ff:ee:dd:cc:bb:aa */
/*
* SDRAM settings & memory map
*/
#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
/*
* SDRAM reference page
* http://docs.blackfin.uclinux.org/doku.php?id=bfin:sdram
* NOTE: BlackVME populates only SDRAM bank 0
*/
/* CONFIG_EBIU_SDBCTL_VAL bank ctrl may be needed in future */
#define CONFIG_EBIU_SDGCTL_VAL 0x91114d /* global control */
#define CONFIG_EBIU_SDRRC_VAL 0x306 /* refresh rate */
/* Async memory global settings. (ASRAM, not SDRAM)
* HRM page 16-10. Global ASRAM control = 0x3F. Six lower bits = 1
* CLKOUT enabled, all async banks enabled, core has priority
* bank 0&1 16 bit (FPGA)
* bank 2&3 32 bit (ether and USB chips)
*/
#define CONFIG_EBIU_AMGCTL_VAL 0x3F /* ASRAM setup */
/* Async mem timing: BF561 HRM page 16-12 and 16-15.
* Default values 0xFFC2 FFC2 are the slowest supported.
* Example settings of CONFIG_EBIU_AMBCTL1_VAL
* 1. EZ-KIT settings: 0xFFC2 7BB0
* 2. Bank 3 good timing for AX88180 @ 125MHz = 0x8850 xxxx
* See the following page:
* http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:ax88180
* 3. Bank 3 timing for AX88180 @ SCLK = 100 MHz:
* AX88180 WEN = 5 clocks REN 6 clocks @ SCLK = 100 MHz
* One extra clock needed because AX88180 is asynchronous to CPU.
*/
/* bank 1 0 */
#define CONFIG_EBIU_AMBCTL0_VAL 0xFFC2FFC2
/* bank 3 2 */
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC2FFC2
/* memory layout */
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
#define CONFIG_SYS_MALLOC_LEN (384 << 10)
/*
* Serial SPI Flash
* For the M25P64 SCK should be kept < 15 MHz
*/
#define CONFIG_BFIN_SPI
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET 0x40000
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x40000
#define CONFIG_ENV_SPI_MAX_HZ 15000000
#define CONFIG_SF_DEFAULT_SPEED 15000000
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_STMICRO
/*
* Interactive command settings
*/
#define CONFIG_SYS_LONGHELP 1
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_AUTO_COMPLETE 1
#include <config_cmd_default.h>
#define CONFIG_CMD_BOOTLDR
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_CPLBINFO
#define CONFIG_CMD_SF
#define CONFIG_CMD_ELF
/*
* Default: boot from SPI flash.
* "sfboot" is a composite command defined in extra settings
*/
#define CONFIG_BOOTDELAY 5
#define CONFIG_BOOTCOMMAND "run sfboot"
/*
* Console settings
*/
#define CONFIG_BAUDRATE 57600
#define CONFIG_LOADS_ECHO 1
#define CONFIG_UART_CONSOLE 0
/*
* U-Boot environment variables. Use "printenv" to examine.
* http://docs.blackfin.uclinux.org/doku.php?id=bootloaders:u-boot:env
*/
#define CONFIG_BOOTARGS \
"root=/dev/mtdblock0 rw " \
"clkin_hz=" __stringify(CONFIG_CLKIN_HZ) " " \
"earlyprintk=serial,uart0," \
__stringify(CONFIG_BAUDRATE) " " \
"console=ttyBF0," __stringify(CONFIG_BAUDRATE) " "
/* Convenience env variables & commands.
* Reserve kernstart = 0x20000 = 128 kB for U-Boot.
* Reserve kernarea = 0x500000 = 5 MB for kernel (reasonable size).
* U-Boot image is saved at flash offset=0.
* Kernel image is saved at flash offset=$kernstart.
* Instructions. Ksave takes about a minute to complete.
* 1. Update U-Boot: run uget; run usave
* 2. Update kernel: run kget; run ksave
* After updating U-Boot also update the kernel per above instructions
* to make the saved environment consistent with the flash.
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
"kernstart=0x20000\0" \
"kernarea=0x500000\0" \
"uget=tftp u-boot.ldr\0" \
"kget=tftp uImage\0" \
"usave=sf probe 2; " \
"sf erase 0 $(kernstart); " \
"sf write $(fileaddr) 0 $(filesize)\0" \
"ksave=sf probe 2; " \
"saveenv; " \
"echo Now patiently wait for the prompt...; " \
"sf erase $(kernstart) $(kernarea); " \
"sf write $(fileaddr) $(kernstart) $(filesize)\0" \
"sfboot=sf probe 2; " \
"sf read $(loadaddr) $(kernstart) $(filesize); " \
"run addip; bootm\0" \
"addip=setenv bootargs $(bootargs) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):" \
"$(netmask):$(hostname):eth0:off\0"
/*
* Soft I2C settings (BF561 does not have hard I2C)
* PF12,13 on SPI connector 0.
*/
#ifdef CONFIG_SYS_I2C_SOFT
# define CONFIG_CMD_I2C
# define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF12
# define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF13
# define CONFIG_SYS_I2C_SPEED 50000
# define CONFIG_SYS_I2C_SLAVE 0xFE
#endif
/*
* No Parallel Flash on this board
*/
#define CONFIG_SYS_NO_FLASH
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_JFFS2
#undef CONFIG_CMD_FLASH
#endif
|
