blob: b179b99468ea56840a34e3a5b3a4ccc3f0e690e9 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
*/
#ifndef _CONFIG_SYNOLOGY_DS414_H
#define _CONFIG_SYNOLOGY_DS414_H
/*
* High Level Configuration Options (easy to change)
*/
/*
* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
* for DDR ECC byte filling in the SPL before loading the main
* U-Boot into it.
*/
#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
/*
* Commands configuration
*/
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_SYS_I2C_SPEED 100000
/* Environment in SPI NOR flash */
#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII
/* PCIe support */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_PCI_SCAN_SHOW
#endif
/* USB/EHCI/XHCI configuration */
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
/* FIXME: broken XHCI support
* Below defines should enable support for the two rear USB3 ports. Sadly, this
* does not work because:
* - xhci-pci seems to not support DM_USB, so with that enabled it is not
* found.
* - USB init fails, controller does not respond in time */
#if !defined(CONFIG_USB_XHCI_HCD)
#define CONFIG_EHCI_IS_TDI
#endif
/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
/*
* Memory layout while starting into the bin_hdr via the
* BootROM:
*
* 0x4000.4000 - 0x4003.4000 headers space (192KiB)
* 0x4000.4030 bin_hdr start address
* 0x4003.4000 - 0x4004.7c00 BootROM memory allocations (15KiB)
* 0x4007.fffc BootROM stack top
*
* The address space between 0x4007.fffc and 0x400f.fff is not locked in
* L2 cache thus cannot be used.
*/
/* SPL */
/* Defines for SPL */
#define CONFIG_SPL_MAX_SIZE ((128 << 10) - 0x4030)
#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))
#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
#if defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI)
/* SPL related SPI defines */
#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
#endif
/* DS414 bus width is 32bits */
#define CONFIG_DDR_32BIT
/* Default Environment */
#define CONFIG_BOOTCOMMAND "sf read ${loadaddr} 0xd0000 0x700000; bootm"
#define CONFIG_LOADADDR 0x80000
#endif /* _CONFIG_SYNOLOGY_DS414_H */
|
