1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
|
/*
* Copyright (C) 2014 Freescale Semiconductor
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __LS2_COMMON_H
#define __LS2_COMMON_H
#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LAYERSCAPE
#define CONFIG_FSL_LSCH3
#define CONFIG_MP
#define CONFIG_GICV3
#define CONFIG_FSL_TZPC_BP147
#include <asm/arch/ls2080a_stream_id.h>
#include <asm/arch/config.h>
#if (defined(CONFIG_SYS_FSL_SRDS_1) || defined(CONFIG_SYS_FSL_SRDS_2))
#define CONFIG_SYS_HAS_SERDES
#endif
/* Link Definitions */
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
/* We need architecture specific misc initializations */
#define CONFIG_ARCH_MISC_INIT
/* Link Definitions */
#ifdef CONFIG_SPL
#define CONFIG_SYS_TEXT_BASE 0x80400000
#else
#define CONFIG_SYS_TEXT_BASE 0x30100000
#endif
#ifdef CONFIG_EMU
#define CONFIG_SYS_NO_FLASH
#endif
#define CONFIG_SUPPORT_RAW_INITRD
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F 1
/* Flat Device Tree Definitions */
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS
/* new uImage format support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
#ifndef CONFIG_SPL
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
#endif
#ifndef CONFIG_SYS_FSL_DDR4
#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
#define CONFIG_SYS_DDR_RAW_TIMING
#endif
#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
/*
* SMP Definitinos
*/
#define CPU_RELEASE_ADDR secondary_boot_func
#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL
/*
* DDR controller use 0 as the base address for binding.
* It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
*/
#define CONFIG_SYS_DP_DDR_BASE_PHY 0
#define CONFIG_DP_DDR_CTRL 2
#define CONFIG_DP_DDR_NUM_CTRLS 1
#endif
/* Generic Timer Definitions */
/*
* This is not an accurate number. It is used in start.S. The frequency
* will be udpated later when get_bus_freq(0) is available.
*/
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)
/* I2C */
#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/* IFC */
#define CONFIG_FSL_IFC
/*
* During booting, IFC is mapped at the region of 0x30000000.
* But this region is limited to 256MB. To accommodate NOR, promjet
* and FPGA. This region is divided as below:
* 0x30000000 - 0x37ffffff : 128MB : NOR flash
* 0x38000000 - 0x3BFFFFFF : 64MB : Promjet
* 0x3C000000 - 0x40000000 : 64MB : FPGA etc
*
* To accommodate bigger NOR flash and other devices, we will map IFC
* chip selects to as below:
* 0x5_1000_0000..0x5_1fff_ffff Memory Hole
* 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
* 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
* 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
* 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
*
* For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
* CONFIG_SYS_FLASH_BASE has the final address (core view)
* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
* CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
* CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
*/
#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000
#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000
#ifndef CONFIG_SYS_NO_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_QUIET_TEST
#endif
#ifndef __ASSEMBLY__
unsigned long long get_qixis_addr(void);
#endif
#define QIXIS_BASE get_qixis_addr()
#define QIXIS_BASE_PHYS 0x20000000
#define QIXIS_BASE_PHYS_EARLY 0xC000000
#define QIXIS_STAT_PRES1 0xb
#define QIXIS_SDID_MASK 0x07
#define QIXIS_ESDHC_NO_ADAPTER 0x7
#define CONFIG_SYS_NAND_BASE 0x530000000ULL
#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000
/* Debug Server firmware */
#define CONFIG_FSL_DEBUG_SERVER
/* 2 sec timeout */
#define CONFIG_SYS_DEBUG_SERVER_TIMEOUT (2 * 1000 * 1000)
/* MC firmware */
#define CONFIG_FSL_MC_ENET
/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
#ifdef CONFIG_LS2085A
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
#endif
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
* It will be used by MC and Debug Server. The MC region must be
* 512MB aligned, so the min size to hide is 512MB.
*/
#if defined(CONFIG_FSL_MC_ENET) || defined(CONFIG_FSL_DEBUG_SERVER)
#define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE (254UL * 1024 * 1024)
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024)
#define CONFIG_SYS_MC_RSV_MEM_ALIGN (512UL * 1024 * 1024)
#endif
/* PCIe */
#define CONFIG_PCIE1 /* PCIE controler 1 */
#define CONFIG_PCIE2 /* PCIE controler 2 */
#define CONFIG_PCIE3 /* PCIE controler 3 */
#define CONFIG_PCIE4 /* PCIE controler 4 */
#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */
#ifdef CONFIG_LS2080A
#define FSL_PCIE_COMPAT "fsl,ls2080a-pcie"
#endif
#ifdef CONFIG_LS2085A
#define FSL_PCIE_COMPAT "fsl,ls2085a-pcie"
#endif
#define CONFIG_SYS_PCI_64BIT
#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000
#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */
#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000
#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */
#define CONFIG_SYS_PCIE_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000
#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */
#define CONFIG_SYS_PCIE_MEM_BUS 0x40000000
#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x40000000
#define CONFIG_SYS_PCIE_MEM_SIZE 0x40000000 /* 1G */
/* Command line configuration */
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ENV
#define CONFIG_CMD_GREPENV
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
#define CONFIG_ARCH_EARLY_INIT_R
/* Physical Memory Map */
/* fixme: these need to be checked against the board */
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
#define CONFIG_NR_DRAM_BANKS 3
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
#define CONFIG_DISPLAY_CPUINFO
/* Allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x80100000\0" \
"kernel_addr=0x100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x581200000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"console=ttyAMA0,38400n8\0"
#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \
"earlycon=uart8250,mmio,0x21c0500" \
"ramdisk_size=0x2000000 default_hugepagesz=2m" \
" hugepagesz=2m hugepages=16"
#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
"$kernel_size && bootm $kernel_load"
#define CONFIG_BOOTDELAY 10
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_MAX_SIZE 0x16000
#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SPL_TEXT_BASE 0x1800a000
#define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#endif /* __LS2_COMMON_H */
|
