blob: 662e601f0fdc940b5c654302641d17c60fa34d76 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2018-2019 NXP
*/
#ifndef __LX2_QDS_H
#define __LX2_QDS_H
#include "lx2160a_common.h"
/* Qixis */
#define QIXIS_XMAP_MASK 0x07
#define QIXIS_XMAP_SHIFT 5
#define QIXIS_RST_CTL_RESET_EN 0x30
#define QIXIS_LBMAP_DFLTBANK 0x00
#define QIXIS_LBMAP_ALTBANK 0x20
#define QIXIS_LBMAP_QSPI 0x00
#define QIXIS_RCW_SRC_QSPI 0xff
#define QIXIS_RST_CTL_RESET 0x31
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
#define QIXIS_LBMAP_MASK 0x0f
#define QIXIS_LBMAP_SD
#define QIXIS_RCW_SRC_SD 0x08
#define NON_EXTENDED_DUTCFG
#define QIXIS_SDID_MASK 0x07
#define QIXIS_ESDHC_NO_ADAPTER 0x7
/* SYSCLK */
#define QIXIS_SYSCLK_100 0x0
#define QIXIS_SYSCLK_125 0x1
#define QIXIS_SYSCLK_133 0x2
/* DDRCLK */
#define QIXIS_DDRCLK_100 0x0
#define QIXIS_DDRCLK_125 0x1
#define QIXIS_DDRCLK_133 0x2
#define BRDCFG4_EMI1SEL_MASK 0xF8
#define BRDCFG4_EMI1SEL_SHIFT 3
#define BRDCFG4_EMI2SEL_MASK 0x07
#define BRDCFG4_EMI2SEL_SHIFT 0
/* VID */
#define I2C_MUX_CH_VOL_MONITOR 0xA
/* Voltage monitor on channel 2*/
#define I2C_VOL_MONITOR_ADDR 0x63
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
#define CONFIG_VID_FLS_ENV "lx2160aqds_vdd_mv"
#define CONFIG_VID
/* The lowest and highest voltage allowed*/
#define VDD_MV_MIN 775
#define VDD_MV_MAX 925
/* PM Bus commands code for LTC3882*/
#define PMBUS_CMD_PAGE 0x0
#define PMBUS_CMD_READ_VOUT 0x8B
#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05
#define PMBUS_CMD_VOUT_COMMAND 0x21
#define PWM_CHANNEL0 0x0
#define CONFIG_VOL_MONITOR_LTC3882_SET
#define CONFIG_VOL_MONITOR_LTC3882_READ
/* RTC */
#define CONFIG_SYS_RTC_BUS_NUM 0
#define I2C_MUX_CH_RTC 0xB
/*
* MMC
*/
#ifdef CONFIG_MMC
#ifndef __ASSEMBLY__
u8 qixis_esdhc_detect_quirk(void);
#endif
#define CONFIG_ESDHC_DETECT_QUIRK qixis_esdhc_detect_quirk()
#endif
/* MAC/PHY configuration */
#if defined(CONFIG_FSL_MC_ENET)
#define CONFIG_MII
#define CONFIG_ETHPRIME "DPMAC17@rgmii-id"
#define AQ_PHY_ADDR1 0x00
#define AQ_PHY_ADDR2 0x01
#define AQ_PHY_ADDR3 0x02
#define AQ_PHY_ADDR4 0x03
#define CORTINA_NO_FW_UPLOAD
#define CORTINA_PHY_ADDR1 0x0
#define INPHI_PHY_ADDR1 0x0
#define INPHI_PHY_ADDR2 0x1
#define RGMII_PHY_ADDR1 0x01
#define RGMII_PHY_ADDR2 0x02
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
#endif
/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
EXTRA_ENV_SETTINGS \
"lx2160aqds_vdd_mv=800\0" \
"BOARD=lx2160aqds\0" \
"xspi_bootcmd=echo Trying load from flexspi..;" \
"sf probe 0:0 && sf read $load_addr " \
"$kernel_start $kernel_size ; env exists secureboot &&" \
"sf read $kernelheader_addr_r $kernelheader_start " \
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
" bootm $load_addr#$BOARD\0" \
"sd_bootcmd=echo Trying load from sd card..;" \
"mmcinfo; mmc read $load_addr " \
"$kernel_addr_sd $kernel_size_sd ;" \
"env exists secureboot && mmc read $kernelheader_addr_r "\
"$kernelhdr_addr_sd $kernelhdr_size_sd " \
" && esbc_validate ${kernelheader_addr_r};" \
"bootm $load_addr#$BOARD\0"
#include <asm/fsl_secure_boot.h>
#endif /* __LX2_QDS_H */
|
