1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
|
/*
* (C) Copyright 2010-2011
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
* esd electronic system design gmbh <www.esd.eu>
*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
* Configuation settings for the esd OTC570 board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* SoC must be defined first, before hardware.h is included.
* In this case SoC is defined in boards.cfg.
*/
#include <asm/hardware.h>
/*
* Warning: changing CONFIG_SYS_TEXT_BASE requires
* adapting the initial boot program.
* Since the linker has to swallow that define, we must use a pure
* hex number here!
*/
#define CONFIG_SYS_TEXT_BASE 0x20002000
/*
* since a number of boards are not being listed in linux
* arch/arm/tools/mach-types any more, the mach-types have to be
* defined here
*/
#define MACH_TYPE_OTC570 2166
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* 32.768 kHz crystal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 16000000/* 16.0 MHz crystal */
/* Misc CPU related */
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SERIAL_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_MISC_INIT_R /* Call misc_init_r */
#define CONFIG_DISPLAY_BOARDINFO /* call checkboard() */
#define CONFIG_DISPLAY_CPUINFO /* display cpu info and speed */
#define CONFIG_PREBOOT /* enable preboot variable */
/*
* Hardware drivers
*/
/* required until arch/arm/include/asm/arch-at91/at91sam9263.h is reworked */
#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
/* general purpose I/O */
#define CONFIG_AT91_GPIO
/* Console output */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK
/* LCD */
#define CONFIG_LCD
#undef CONFIG_SPLASH_SCREEN
#ifdef CONFIG_LCD
# define LCD_BPP LCD_COLOR8
# ifndef CONFIG_SPLASH_SCREEN
# define CONFIG_LCD_LOGO
# define CONFIG_LCD_INFO
# undef CONFIG_LCD_INFO_BELOW_LOGO
# endif /* CONFIG_SPLASH_SCREEN */
# undef LCD_TEST_PATTERN
# define CONFIG_SYS_WHITE_ON_BLACK
# define CONFIG_ATMEL_LCD
# define CONFIG_SYS_CONSOLE_IS_IN_ENV
# define CONFIG_OTC570_LCD_BASE (CONFIG_SYS_SDRAM_BASE + 0x03fa5000)
# define CONFIG_CMD_BMP
#endif /* CONFIG_LCD */
/* RTC and I2C stuff */
#define CONFIG_RTC_DS1338
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
#ifdef CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C_SOFT_SPEED 100000
#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
/* Configure data and clock pins for pio */
# define I2C_INIT { \
at91_set_pio_output(AT91_PIO_PORTB, 4, 0); \
at91_set_pio_output(AT91_PIO_PORTB, 5, 0); \
}
# define I2C_SOFT_DECLARATIONS
/* Configure data pin as output */
# define I2C_ACTIVE at91_set_pio_output(AT91_PIO_PORTB, 4, 0)
/* Configure data pin as input */
# define I2C_TRISTATE at91_set_pio_input(AT91_PIO_PORTB, 4, 0)
/* Read data pin */
# define I2C_READ at91_get_pio_value(AT91_PIO_PORTB, 4)
/* Set data pin */
# define I2C_SDA(bit) at91_set_pio_value(AT91_PIO_PORTB, 4, bit)
/* Set clock pin */
# define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTB, 5, bit)
# define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
#endif /* CONFIG_SYS_I2C_SOFT */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_IMLS
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_NAND
#define CONFIG_CMD_USB
#define CONFIG_CMD_I2C
#define CONFIG_CMD_DATE
/* LED */
#define CONFIG_AT91_LED
/*
* SDRAM: 1 bank, min 32, max 128 MB
* Initialized before u-boot gets started.
*/
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE 0x20000000 /* ATMEL_BASE_CS1 */
#define CONFIG_SYS_SDRAM_SIZE 0x04000000
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x00100000)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01E00000)
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x00100000)
/*
* Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM,
* leaving the correct space for initial global data structure above
* that address while providing maximum stack area below.
*/
#define CONFIG_SYS_INIT_SP_ADDR \
(ATMEL_BASE_SRAM0 + 0x1000 - GENERATED_GBL_DATA_SIZE)
/* DataFlash */
#ifdef CONFIG_SYS_USE_DATAFLASH
# define CONFIG_ATMEL_DATAFLASH_SPI
# define CONFIG_HAS_DATAFLASH
# define CONFIG_SYS_MAX_DATAFLASH_BANKS 1
# define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */
# define AT91_SPI_CLK 15000000
# define DATAFLASH_TCSS (0x1a << 16)
# define DATAFLASH_TCHS (0x1 << 24)
#endif
/* NOR flash is not populated, disable it */
#define CONFIG_SYS_NO_FLASH
/* NAND flash */
#ifdef CONFIG_CMD_NAND
# define CONFIG_NAND_ATMEL
# define CONFIG_SYS_MAX_NAND_DEVICE 1
# define CONFIG_SYS_NAND_BASE 0x40000000 /* ATMEL_BASE_CS3 */
# define CONFIG_SYS_NAND_DBW_8
# define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
# define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
# define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15)
# define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PA(22)
#endif
/* Ethernet */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_FIT
#define CONFIG_NET_RETRY_COUNT 20
#undef CONFIG_RESET_PHY_R
/* USB */
#define CONFIG_USB_ATMEL
#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
#define CONFIG_USB_STORAGE
#define CONFIG_CMD_FAT
/* CAN */
#define CONFIG_AT91_CAN
/* hw-controller addresses */
#define CONFIG_ET1100_BASE 0x70000000 /* ATMEL_BASE_CS6 */
#ifdef CONFIG_SYS_USE_DATAFLASH
/* bootstrap + u-boot + env in dataflash on CS0 */
# define CONFIG_ENV_IS_IN_DATAFLASH
# define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
0x8400)
# define CONFIG_ENV_OFFSET 0x4200
# define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
CONFIG_ENV_OFFSET)
# define CONFIG_ENV_SIZE 0x4200
#elif CONFIG_SYS_USE_NANDFLASH
/* bootstrap + u-boot + env + linux in nandflash */
# define CONFIG_ENV_IS_IN_NAND 1
# define CONFIG_ENV_OFFSET 0xC0000
# define CONFIG_ENV_SIZE 0x20000
#endif
#define CONFIG_SYS_CBSIZE 512
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + \
128*1024, 0x1000)
#endif
|
