1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2008
* Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com.
*
* Wolfgang Denk <wd@denx.de>
* Copyright 2004 Freescale Semiconductor.
* (C) Copyright 2002,2003 Motorola,Inc.
* Xianghua Xiao <X.Xiao@motorola.com>
*/
/*
* Socrates
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* Only possible on E500 Version 2 or newer cores.
*/
/*
* sysclk for MPC85xx
*
* Two valid values are:
* 33000000
* 66000000
*
* Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
* is likely the desired value here, so that is now the default.
* The board, however, can run at 66MHz. In any event, this value
* must match the settings of some switches. Details can be found
* in the README.mpc85xxads.
*/
#define CFG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
#undef CFG_SYS_DRAM_TEST /* memory test, takes time */
#define CFG_SYS_CCSRBAR 0xE0000000
#define CFG_SYS_CCSRBAR_PHYS_LOW CFG_SYS_CCSRBAR
/* DDR Setup */
#define CFG_SYS_DDR_SDRAM_BASE 0x00000000
#define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE
/* I2C addresses of SPD EEPROMs */
#define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */
/* Hardcoded values, to use instead of SPD */
#define CFG_SYS_DDR_CS0_BNDS 0x0000000f
#define CFG_SYS_DDR_CS0_CONFIG 0x80010102
#define CFG_SYS_DDR_TIMING_0 0x00260802
#define CFG_SYS_DDR_TIMING_1 0x3935D322
#define CFG_SYS_DDR_TIMING_2 0x14904CC8
#define CFG_SYS_DDR_MODE 0x00480432
#define CFG_SYS_DDR_INTERVAL 0x030C0100
#define CFG_SYS_DDR_CONFIG_2 0x04400000
#define CFG_SYS_DDR_CONFIG 0xC3008000
#define CFG_SYS_DDR_CLK_CONTROL 0x03800000
#define CFG_SYS_SDRAM_SIZE 256 /* in Megs */
/*
* Flash on the LocalBus
*/
#define CFG_SYS_FLASH0 0xFE000000
#define CFG_SYS_FLASH_BANKS_LIST { CFG_SYS_FLASH0 }
#define CFG_SYS_LBC_FLASH_BASE CFG_SYS_FLASH0 /* Localbus flash start */
#define CFG_SYS_FLASH_BASE CFG_SYS_LBC_FLASH_BASE /* start of FLASH */
#define CFG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
#define CFG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
#define CFG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
#define CFG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/
#define CFG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CFG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM*/
#define CFG_SYS_INIT_SP_OFFSET (CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/* FPGA and NAND */
#define CFG_SYS_FPGA_BASE 0xc0000000
#define CFG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */
#define CFG_SYS_NAND_BASE (CFG_SYS_FPGA_BASE + 0x70)
/* LIME GDC */
#define CFG_SYS_LIME_BASE 0xc8000000
/*
* General PCI
* Memory space is mapped 1-1.
*/
#define CFG_SYS_PCI1_MEM_PHYS 0x80000000
#define CFG_SYS_PCI1_IO_PHYS 0xE2000000
/*
* Miscellaneous configurable options
*/
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
#define CFG_ENV_FLAGS_LIST_STATIC "ethaddr:mw,eth1addr:mw,system1_addr:xw,serial#:sw,ethact:sw,ethprime:sw"
/* pass open firmware flat tree */
#endif /* __CONFIG_H */
|
