1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* ti_armv7_common.h
*
* Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
*
* The various ARMv7 SoCs from TI all share a number of IP blocks when
* implementing a given feature. Rather than define these in every
* board or even SoC common file, we define a common file to be re-used
* in all cases. While technically true that some of these details are
* configurable at the board design, they are common throughout SoC
* reference platforms as well as custom designs and become de facto
* standards.
*/
#ifndef __CONFIG_TI_ARMV7_COMMON_H__
#define __CONFIG_TI_ARMV7_COMMON_H__
/*
* We setup defaults based on constraints from the Linux kernel, which should
* also be safe elsewhere. We have the default load at 32MB into DDR (for
* the kernel), FDT above 128MB (the maximum location for the end of the
* kernel), and the ramdisk 512KB above that (allowing for hopefully never
* seen large trees). We say all of this must be within the first 256MB
* as that will normally be within the kernel lowmem and thus visible via
* bootm_size and we only run on platforms with 256MB or more of memory.
*
* As a temporary storage for DTBO blobs (which should be applied into DTB
* blob), we use the location 15.5 MB above the ramdisk. If someone wants to
* use ramdisk bigger than 15.5 MB, then DTBO can be loaded and applied to DTB
* blob before loading the ramdisk, as DTBO location is only used as a temporary
* storage, and can be re-used after 'fdt apply' command is done.
*/
#define DEFAULT_LINUX_BOOT_ENV \
"loadaddr=0x82000000\0" \
"kernel_addr_r=0x82000000\0" \
"fdtaddr=0x88000000\0" \
"dtboaddr=0x89000000\0" \
"fdt_addr_r=0x88000000\0" \
"fdtoverlay_addr_r=0x89000000\0" \
"rdaddr=0x88080000\0" \
"ramdisk_addr_r=0x88080000\0" \
"scriptaddr=0x80000000\0" \
"pxefile_addr_r=0x80100000\0" \
"bootm_size=0x10000000\0" \
"boot_fdt=try\0"
#define DEFAULT_FIT_TI_ARGS \
"boot_fit=0\0" \
"addr_fit=0x90000000\0" \
"name_fit=fitImage\0" \
"update_to_fit=setenv loadaddr ${addr_fit}; setenv bootfile ${name_fit}\0" \
"get_overlaystring=" \
"for overlay in $name_overlays;" \
"do;" \
"setenv overlaystring ${overlaystring}'#'${overlay};" \
"done;\0" \
"run_fit=bootm ${addr_fit}#conf-${fdtfile}${overlaystring}\0" \
/*
* DDR information. If the CONFIG_NR_DRAM_BANKS is not defined,
* we say (for simplicity) that we have 1 bank, always, even when
* we have more. We always start at 0x80000000, and we place the
* initial stack pointer in our SRAM. Otherwise, we can define
* CONFIG_NR_DRAM_BANKS before including this file.
*/
#define CONFIG_SYS_SDRAM_BASE 0x80000000
/* If DM_I2C, enable non-DM I2C support */
/*
* The following are general good-enough settings for U-Boot. We set a
* large malloc pool as we generally have a lot of DDR, and we opt for
* function over binary size in the main portion of U-Boot as this is
* generally easily constrained later if needed. We enable the config
* options that give us information in the environment about what board
* we are on so we do not need to rely on the command prompt. We set a
* console baudrate of 115200 and use the default baud rate table.
*/
/* As stated above, the following choices are optional. */
/* Console I/O Buffer Size */
/*
* When we have SPI, NOR or NAND flash we expect to be making use of
* mtdparts, both for ease of use in U-Boot and for passing information
* on to the Linux kernel.
*/
/*
* Our platforms make use of SPL to initalize the hardware (primarily
* memory) enough for full U-Boot to be loaded. We make use of the general
* SPL framework found under common/spl/. Given our generally common memory
* map, we set a number of related defaults and sizes here.
*/
#if !defined(CONFIG_NOR_BOOT) && \
!(defined(CONFIG_QSPI_BOOT) && defined(CONFIG_AM43XX))
/*
* We also support Falcon Mode so that the Linux kernel can be booted
* directly from SPL. This is not currently available on HS devices.
*/
/*
* Place the image at the start of the ROM defined image space (per
* CONFIG_SPL_TEXT_BASE and we limit our size to the ROM-defined
* downloaded image area minus 1KiB for scratch space. We initalize DRAM as
* soon as we can so that we can place stack, malloc and BSS there. We load
* U-Boot itself into memory at 0x80800000 for legacy reasons (to not conflict
* with older SPLs). We have our BSS be placed 2MiB after this, to allow for
* the default Linux kernel address of 0x80008000 to work with most sized
* kernels, in the Falcon Mode case. We have the SPL malloc pool at the end
* of the BSS area. We suggest that the stack be placed at 32MiB after the
* start of DRAM to allow room for all of the above (handled in Kconfig).
*/
#ifdef CONFIG_SPL_OS_BOOT
/* FAT */
/* RAW SD card / eMMC */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x1500 /* address 0x2A0000 */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x200 /* 256KiB */
#endif
/* General parts of the framework, required. */
#ifdef CONFIG_MTD_RAW_NAND
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#endif
#endif /* !CONFIG_NOR_BOOT */
/* Generic Environment Variables */
#ifdef CONFIG_CMD_NET
#define NETARGS \
"static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
"::off\0" \
"nfsopts=nolock\0" \
"rootpath=/export/rootfs\0" \
"netloadimage=tftp ${loadaddr} ${bootfile}\0" \
"netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
"netargs=setenv bootargs console=${console} " \
"${optargs} " \
"root=/dev/nfs " \
"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
"ip=dhcp\0" \
"netboot=echo Booting from network ...; " \
"setenv autoload no; " \
"dhcp; " \
"run netloadimage; " \
"run netloadfdt; " \
"run netargs; " \
"bootz ${loadaddr} - ${fdtaddr}\0"
#else
#define NETARGS ""
#endif
#endif /* __CONFIG_TI_ARMV7_COMMON_H__ */
|
