ppc4xx: remove HUB405 board

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>

5 files changed, 0 insertions, 321 deletions

diff --git a/board/esd/hub405/Kconfig b/board/esd/hub405/Kconfig
deleted file mode 100644
index 2b9556a195e..00000000000
--- a/board/esd/hub405/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_HUB405
-
-config SYS_BOARD
-	default "hub405"
-
-config SYS_VENDOR
-	default "esd"
-
-config SYS_CONFIG_NAME
-	default "HUB405"
-
-endif
diff --git a/board/esd/hub405/MAINTAINERS b/board/esd/hub405/MAINTAINERS
deleted file mode 100644
index e84a1d95f25..00000000000
--- a/board/esd/hub405/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-HUB405 BOARD
-M:	Matthias Fuchs <matthias.fuchs@esd-electronics.com>
-S:	Maintained
-F:	board/esd/hub405/
-F:	include/configs/HUB405.h
-F:	configs/HUB405_defconfig
diff --git a/board/esd/hub405/Makefile b/board/esd/hub405/Makefile
deleted file mode 100644
index 99e18b567fd..00000000000
--- a/board/esd/hub405/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= hub405.o flash.o \
-	../common/misc.o \
-	../common/esd405ep_nand.o \
diff --git a/board/esd/hub405/flash.c b/board/esd/hub405/flash.c
deleted file mode 100644
index 23e81642e02..00000000000
--- a/board/esd/hub405/flash.c
+++ /dev/null
@@ -1,85 +0,0 @@
-/*
- * (C) Copyright 2001
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/processor.h>
-
-/*
- * include common flash code (for esd boards)
- */
-#include "../common/flash.c"
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long * addr, flash_info_t * info);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	unsigned long size_b0;
-	int i;
-	uint pbcr;
-	unsigned long base_b0;
-	int size_val = 0;
-
-	/* Init: no FLASHes known */
-	for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-	}
-
-	/* Static FLASH Bank configuration here - FIXME XXX */
-
-	size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
-
-	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
-		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
-			size_b0, size_b0<<20);
-	}
-
-	/* Setup offsets */
-	flash_get_offsets (-size_b0, &flash_info[0]);
-
-	/* Re-do sizing to get full correct info */
-	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(EBC0_CFGADDR, PB0CR);
-	base_b0 = -size_b0;
-	switch (size_b0) {
-	case 1 << 20:
-		size_val = 0;
-		break;
-	case 2 << 20:
-		size_val = 1;
-		break;
-	case 4 << 20:
-		size_val = 2;
-		break;
-	case 8 << 20:
-		size_val = 3;
-		break;
-	case 16 << 20:
-		size_val = 4;
-		break;
-	}
-	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(EBC0_CFGDATA, pbcr);
-
-	/* Monitor protection ON by default */
-	(void)flash_protect(FLAG_PROTECT_SET,
-			    -CONFIG_SYS_MONITOR_LEN,
-			    0xffffffff,
-			    &flash_info[0]);
-
-	flash_info[0].size = size_b0;
-
-	return (size_b0);
-}
diff --git a/board/esd/hub405/hub405.c b/board/esd/hub405/hub405.c
deleted file mode 100644
index 14237443fa5..00000000000
--- a/board/esd/hub405/hub405.c
+++ /dev/null
@@ -1,208 +0,0 @@
-/*
- * (C) Copyright 2001-2003
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <command.h>
-#include <malloc.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-extern void lxt971_no_sleep(void);
-
-int board_revision(void)
-{
-	unsigned long osrl_reg;
-	unsigned long isr1l_reg;
-	unsigned long tcr_reg;
-	unsigned long value;
-
-	/*
-	 * Get version of HUB405 board from GPIO's
-	 */
-
-	/*
-	 * Setup GPIO pin(s) (IRQ6/GPIO23)
-	 */
-	osrl_reg = in_be32((void *)GPIO0_OSRH);
-	isr1l_reg = in_be32((void *)GPIO0_ISR1H);
-	tcr_reg = in_be32((void *)GPIO0_TCR);
-	out_be32((void *)GPIO0_OSRH, osrl_reg & ~0x00030000);     /* output select */
-	out_be32((void *)GPIO0_ISR1H, isr1l_reg | 0x00030000);    /* input select  */
-	out_be32((void *)GPIO0_TCR, tcr_reg & ~0x00000100);       /* select input  */
-
-	udelay(1000);            /* wait some time before reading input */
-	value = in_be32((void *)GPIO0_IR) & 0x00000100;         /* get config bits */
-
-	/*
-	 * Restore GPIO settings
-	 */
-	out_be32((void *)GPIO0_OSRH, osrl_reg);                   /* output select */
-	out_be32((void *)GPIO0_ISR1H, isr1l_reg);                 /* input select  */
-	out_be32((void *)GPIO0_TCR, tcr_reg);  /* enable output driver for outputs */
-
-	if (value & 0x00000100) {
-		/* Revision 1.1 or 1.2 detected */
-		return 1;
-	}
-
-	/* Revision 1.0 */
-	return 0;
-}
-
-
-int board_early_init_f (void)
-{
-	/*
-	 * IRQ 0-15  405GP internally generated; active high; level sensitive
-	 * IRQ 16    405GP internally generated; active low; level sensitive
-	 * IRQ 17-24 RESERVED
-	 * IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
-	 * IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
-	 * IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
-	 * IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
-	 * IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
-	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
-	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
-	 */
-	mtdcr(UIC0SR, 0xFFFFFFFF);       /* clear all ints */
-	mtdcr(UIC0ER, 0x00000000);       /* disable all ints */
-	mtdcr(UIC0CR, 0x00000000);       /* set all to be non-critical*/
-	mtdcr(UIC0PR, 0xFFFFFF9F);       /* set int polarities */
-	mtdcr(UIC0TR, 0x10000000);       /* set int trigger levels */
-	mtdcr(UIC0VCR, 0x00000001);      /* set vect base=0,INT0 highest priority*/
-	mtdcr(UIC0SR, 0xFFFFFFFF);       /* clear all ints */
-
-	/*
-	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
-	 */
-	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
-
-	return 0;
-}
-
-#define LED_REG (DUART0_BA + 0x20)
-int misc_init_r (void)
-{
-	unsigned long val;
-	int delay, flashcnt;
-	char *str;
-	char hw_rev[4];
-
-	/*
-	 * Enable interrupts in exar duart mcr[3]
-	 */
-	out_8((void *)(DUART0_BA + 4), 0x08);
-	out_8((void *)(DUART1_BA + 4), 0x08);
-	out_8((void *)(DUART2_BA + 4), 0x08);
-	out_8((void *)(DUART3_BA + 4), 0x08);
-
-	/*
-	 * Set RS232/RS422 control (RS232 = high on GPIO)
-	 */
-	val = in_be32((void *)GPIO0_OR);
-	val &= ~(CONFIG_SYS_UART2_RS232 | CONFIG_SYS_UART3_RS232 |
-		 CONFIG_SYS_UART4_RS232 | CONFIG_SYS_UART5_RS232);
-
-	str = getenv("phys0");
-	if (!str || (str && (str[0] == '0')))
-		val |= CONFIG_SYS_UART2_RS232;
-
-	str = getenv("phys1");
-	if (!str || (str && (str[0] == '0')))
-		val |= CONFIG_SYS_UART3_RS232;
-
-	str = getenv("phys2");
-	if (!str || (str && (str[0] == '0')))
-		val |= CONFIG_SYS_UART4_RS232;
-
-	str = getenv("phys3");
-	if (!str || (str && (str[0] == '0')))
-		val |= CONFIG_SYS_UART5_RS232;
-
-	out_be32((void *)GPIO0_OR, val);
-
-	/*
-	 * check board type and setup AP power
-	 */
-	str = getenv("bd_type"); /* this is only set on non prototype hardware */
-	if (str != NULL) {
-		if ((strcmp(str, "swch405") == 0) || ((!strcmp(str, "hub405") && (gd->board_type >= 1)))) {
-			unsigned char led_reg_default = 0;
-			str = getenv("ap_pwr");
-			if (!str || (str && (str[0] == '1')))
-				led_reg_default = 0x04 | 0x02 ; /* U2_LED | AP_PWR */
-
-			/*
-			 * Flash LEDs
-			 */
-			for (flashcnt = 0; flashcnt < 3; flashcnt++) {
-				/* LED_A..D off */
-				out_8((void *)LED_REG, led_reg_default);
-				for (delay = 0; delay < 100; delay++)
-					udelay(1000);
-				/* LED_A..D on */
-				out_8((void *)LED_REG, led_reg_default | 0xf0);
-				for (delay = 0; delay < 50; delay++)
-					udelay(1000);
-			}
-			out_8((void *)LED_REG, led_reg_default);
-		}
-	}
-
-	/*
-	 * Reset external DUARTs
-	 */
-	out_be32((void *)GPIO0_OR,
-		 in_be32((void *)GPIO0_OR) | CONFIG_SYS_DUART_RST); /* set reset to high */
-	udelay(10); /* wait 10us */
-	out_be32((void *)GPIO0_OR,
-		 in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_DUART_RST); /* set reset to low */
-	udelay(1000); /* wait 1ms */
-
-	/*
-	 * Store hardware revision in environment for further processing
-	 */
-	sprintf(hw_rev, "1.%ld", gd->board_type);
-	setenv("hw_rev", hw_rev);
-	return (0);
-}
-
-
-/*
- * Check Board Identity:
- */
-int checkboard (void)
-{
-	char str[64];
-	int i = getenv_f("serial#", str, sizeof(str));
-
-	puts ("Board: ");
-
-	if (i == -1) {
-		puts ("### No HW ID - assuming HUB405");
-	} else {
-		puts(str);
-	}
-
-	if (getenv_f("bd_type", str, sizeof(str)) != -1) {
-		printf(" (%s", str);
-	} else {
-		puts(" (Missing bd_type!");
-	}
-
-	gd->board_type = board_revision();
-	printf(", Rev 1.%ld)\n", gd->board_type);
-
-	/*
-	 * Disable sleep mode in LXT971
-	 */
-	lxt971_no_sleep();
-
-	return 0;
-}